Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Compact orange 3D printed stand with OLED screen and built in fan

Bitaxe

Bitaxe NerdOCTaxe Rev3.1 12 TH/s mining hardware

SKU CH-RFDX-023QD

A compact open-source ASIC solo miner delivering 12 TH/s at 200 W with BM1370 chip, 2.4 GHz Wi-Fi, AxeOS firmware, and a 0.91" OLED display

  • TypeMining Power Supply
  • Crypto AlgorithmBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky
  • Compatible CurrencyWrapped Bitcoin (WBTC)
  • Mining HardwareBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky
  • HashrateBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky
  • Network ConnectionBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky
  • 12 TH/s hashrate powered by BM1370 ASIC chip
  • 200 W total power draw at 1516 J/TH efficiency
  • 4 GHz Wi-Fi and AxeOS for remote monitoring
  • 91" OLED shows real-time stats instantly
  • Active air cooling with brushless fan for quiet operation

Solo Bitcoin ASIC Miner

The Bitaxe NerdOCTaxe Rev3.1 is a compact open-source ASIC solo miner designed for home or office Bitcoin mining. It uses the BM1370 chip to deliver a hashrate of 12 TH/s while drawing 200W of power. The device supports the SHA256 algorithm and connects via 2.4GHz Wi-Fi. A built-in 0.91 inch OLED display shows real-time statistics.

Efficiency and Hashrate

The single specification that determines suitability is the energy efficiency of 1516 J/TH at 12 TH/s. This figure directly governs daily electricity cost versus the probability of solving a block. Buyers should compare this efficiency against their local power rate before purchasing.

Setup and Common Issues

Initial setup requires only mains power and a 2.4GHz Wi-Fi network; the AxeOS firmware configures mining parameters automatically. The most frequent issue is unstable 2.4GHz connectivity causing dropped shares. The solder-free modular design allows the BM1370 hash board to be swapped without special tools if a chip fails.

Kohokohdat

  • 12 TH/s hashrate powered by BM1370 ASIC chip
  • 200 W total power draw at 1516 J/TH efficiency
  • 4 GHz Wi-Fi and AxeOS for remote monitoring
  • 91" OLED shows real-time stats instantly
  • Active air cooling with brushless fan for quiet operation

Tekniset tiedot

Model12T
TypeMining Power Supply
Crypto AlgorithmBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky Crypto Lottery Miner with Open-Source System, 200W Low Power Home Solo ASIC Miner Bitcoin ASIC Solo Miner, BM1370 Chip, 2.4G Wi-Fi, AxeOS
Compatible CurrencyWrapped Bitcoin (WBTC)
Mining HardwareBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky Crypto Lottery Miner with Open-Source System, 200W Low Power Home Solo ASIC Miner Bitcoin ASIC Solo Miner, BM1370 Chip, 2.4G Wi-Fi, AxeOS
HashrateBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky Crypto Lottery Miner with Open-Source System, 200W Low Power Home Solo ASIC Miner Bitcoin ASIC Solo Miner, BM1370 Chip, 2.4G Wi-Fi, AxeOS
Network ConnectionBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky Crypto Lottery Miner with Open-Source System, 200W Low Power Home Solo ASIC Miner Bitcoin ASIC Solo Miner, BM1370 Chip, 2.4G Wi-Fi, AxeOS
FanBuilt-in High-speed Brushless Fan
Dimension14.33in W x 12.83in H x 9.06in D
Weight0.5 pounds
FeatureBitcoins Miner NerdOCTaxe ? Rev3.1 ASIC Miner, 12TH/S Lucky Crypto Lottery Miner with Open-Source System, 200W Low Power Home Solo ASIC Miner Bitcoin ASIC Solo Miner, BM1370 Chip, 2.4G Wi-Fi, AxeOS, 1

Kysymyksiä tästä tuotteesta

What power input does the miner need?

The unit draws 200 W and connects via USB, so a standard USB power source rated for that wattage is required.

Does the built-in Wi-Fi work with 5 GHz networks?

The wireless module operates on 2.4 GHz only, so a 2.4 GHz access point or router band is needed.

How much space should I allow for the device and its stand?

The miner measures 14.33 in wide, 12.83 in high and 9.06 in deep, and the orange 3D-printed stand fits within that footprint.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.