Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Buffalo Technology 2 TB 3.5-inch SATA internal hard drive

Buffalo Technology

Buffalo Technology OP-HD 2.0 /A 2 TB internal hard drive

SKU CH-26B9-EDCWV

A 2 TB SATA hard drive built as a direct replacement for LinkStation 420 NVR units

  • 2 TB capacity stores large media libraries and backups
  • SATA III interface provides fast transfer rates for NVR recording
  • Designed as direct replacement for LS420D0402S model
  • Engineered for durability in continuous NVR operation
  • Optimised for LinkStation 420 NVR compatibility

Direct Replacement for LinkStation 420 NVR

The Buffalo Technology OP-HD 2.0 /A is a 2 TB internal hard drive built specifically for the LinkStation 420 NVR. It serves as a direct replacement for the LS420D0402S model, ensuring full compatibility with that network video recorder. The drive uses a SATA interface to deliver reliable data transfer for continuous recording workloads. It is intended for owners of that specific NVR who need to restore or expand storage capacity.

Upgrade from a Failed or Smaller Original Drive

This drive replaces the original hard drive that shipped with the LinkStation 420 NVR when that drive fails or when the 2 TB capacity is required. The jump is worth it when the NVR shows drive errors, capacity limits are reached, or a fresh drive is needed for a clean installation. It matches the factory specifications so the recorder recognises it immediately without firmware mismatches. Buyers who need more than 2 TB or a different form factor cannot use this model.

Simple Tray Swap with No Extra Configuration

Installation consists of removing the NVR drive tray, swapping the old drive for this one, and reinserting the tray. The LinkStation 420 NVR detects the new drive automatically and prompts for initialisation through its standard interface. What usually goes wrong is skipping the initialisation step or using a drive from a different NVR series, which the recorder will reject. No additional cables, brackets, or software tools are required beyond the unit’s own menus.

Kohokohdat

  • 2 TB capacity stores large media libraries and backups
  • SATA III interface provides fast transfer rates for NVR recording
  • Designed as direct replacement for LS420D0402S model
  • Engineered for durability in continuous NVR operation
  • Optimised for LinkStation 420 NVR compatibility

Tekniset tiedot

Tälle tuotteelle ei ole vielä julkaistu teknisiä tietoja.

Kysymyksiä tästä tuotteesta

What drive bay size and interface does the OP-HD 2.0 /A need to fit a LinkStation 420 NVR?

The drive uses a standard SATA III interface and matches the 3.5-inch form factor required by the LinkStation 420 NVR chassis.

What is the correct installation sequence for the OP-HD 2.0 /A in a LinkStation 420 NVR, and which step is most often missed?

Power off the NVR, open the drive bay, connect both SATA data and power cables firmly, secure the drive with the supplied screws, then close the bay before powering on; the step most often missed is tightening the mounting screws.

How do I know when the OP-HD 2.0 /A should be replaced in a LinkStation 420 NVR?

Monitor the NVR's SMART health alerts for reallocated sectors or rising error counts, and replace the drive if the status changes from healthy to warning or fail.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.