Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Dark blue PTFE Bowden tubing coil, 1 metre length, 6.35 mm outer diameter

CAPRICORN

CAPRICORN PTFE Bowden XS Series Tubing 1m 2.85mm Filament 3.2mm ID

SKU CH-EGJ8-7D6W2

PTFE Bowden tubing with a 3.2 mm inner diameter and friction-reducing additive for smooth feeding of 2.85 mm flexible filaments

  • Reduces filament friction with unique additive treatment
  • Precisely constrains 2.85mm filament via 3.2mm inner diameter
  • Perfectly round bore minimises buckling on flexible 3.00mm materials
  • Pure PTFE construction delivers consistent extrusion performance
  • One metre length suits direct Bowden upgrades

CAPRICORN PTFE Bowden XS Series Tubing

This one-metre length of PTFE tubing is designed for Bowden-style 3D printers that use 2.85 mm filament. Its 3.2 mm inner diameter provides a precise path from the extruder to the hotend. The tubing suits makers who need reliable filament constraint on softer materials. It comes in a dark blue finish.

3.2 mm Inner Diameter Capacity and Headroom

The tight 3.2 mm bore reduces filament buckling and compression inside the guide tube. A unique friction-reducing additive helps softer 3.00 mm filaments slide with less resistance. The consistent roundness maintains steady flow during long prints. It is less suited for rigid filaments that require a looser fit.

6.35 mm Outer Diameter Interface Limits

The 6.35 mm outer diameter fits standard Bowden couplers and fittings used on many desktop printers. One metre of tubing covers typical extruder-to-hotend distances without joins. Builds with longer cable runs will need additional lengths. The pure PTFE construction handles normal hotend temperatures for common filaments.

Kohokohdat

  • Reduces filament friction with unique additive treatment
  • Precisely constrains 2.85mm filament via 3.2mm inner diameter
  • Perfectly round bore minimises buckling on flexible 3.00mm materials
  • Pure PTFE construction delivers consistent extrusion performance
  • One metre length suits direct Bowden upgrades

Tekniset tiedot

BrandCapricorn
ModelXS Series

Kysymyksiä tästä tuotteesta

Will the 3.2 mm inner diameter constrain 2.85 mm filament tightly enough to stop buckling in my existing Bowden setup?

The 3.2 mm bore leaves only a small clearance around 2.85 mm filament, reducing the space where softer material can compress or kink between the extruder and hotend.

How can I verify the tubing is seated correctly after I install it?

Push the tube fully into the push-fit couplers at both ends; the dark blue PTFE should sit flush with no visible gap, and filament should feed smoothly without catching on a misaligned edge.

Does the 1 metre length include any fittings or cutter, or do I need to source push-fit connectors and a sharp blade separately?

The pack contains only the 1 metre length of 6.35 mm OD tubing; push-fit connectors and a clean cutting tool must be purchased separately.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.