Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with black chips and gold edge contacts

Computer Memory Solutions

Computer Memory Solutions 512MB DDR1 333MHz SODIMM memory upgrade

SKU CH-6NRV-K1NKH

512 MB DDR1 333 MHz SODIMM module upgrades compatible Xerox Phaser 8560 printers

  • Capacity512MB
  • Type200-Pin DDR SO-DIMM
  • SpeedDDR 333 (PC 2700)
  • CAS LatencyCL2.5
  • Timing3-3-3
  • Voltage2.5V
  • 512 MB capacity expands printer memory for larger print jobs
  • DDR1 333 MHz speed matches the Xerox Phaser 8560 specifications
  • 200-pin SODIMM form factor fits the printer's memory slots directly
  • Non-ECC unbuffered design ensures stable operation in the target device
  • CL2.5 latency with 3-3-3 timing delivers responsive data access

System-specific DDR1 SODIMM for Xerox Phaser 8560

This 512 MB DDR1 333 MHz SODIMM is built for the Xerox Phaser 8560 MFC, 8560MFPD, 8560MFP and 8560DX printers. It uses a 200-pin unbuffered non-ECC design running at 2.5 V with CL2.5 timing. The module is sold as a single stick to add memory to the listed devices.

Fits the named Phaser 8560 models.

The memory is validated only for the four Xerox Phaser 8560 variants shown in the compatibility list. It will not work in laptops, desktops or other printers that require different pin counts, voltages or ECC support. Buyers needing more than 512 MB per slot or a different speed grade should look elsewhere.

200-pin DDR1 SO-DIMM interface decides fit

The module uses the 200-pin DDR1 SO-DIMM form factor with PC2700 333 MHz signalling. This single physical and electrical interface determines whether the part installs and functions in the target printer. Confirm the socket type matches before purchase.

Kohokohdat

  • 512 MB capacity expands printer memory for larger print jobs
  • DDR1 333 MHz speed matches the Xerox Phaser 8560 specifications
  • 200-pin SODIMM form factor fits the printer's memory slots directly
  • Non-ECC unbuffered design ensures stable operation in the target device
  • CL2.5 latency with 3-3-3 timing delivers responsive data access

Tekniset tiedot

BrandComputer Memory Solutions
ModelCM64642700SO16C
Capacity512MB
Type200-Pin DDR SO-DIMM
SpeedDDR 333 (PC 2700)
CAS LatencyCL2.5
Timing3-3-3
Voltage2.5V
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor Brand Chipset
Heat SpreaderNo
Compatible SystemXerox Phaser 8560 Mfc, 8560Mfpd, 8560Mfp, 8560Dx
Package Content1 Memory RAM Stick

Kysymyksiä tästä tuotteesta

Does the Phaser 8560 need any free 200-pin SODIMM slots before I install this module?

The Phaser 8560 has two SODIMM sockets; at least one must be free to accept the 512MB stick.

Can I keep the original memory in the second slot while adding this DDR1 333MHz stick?

Yes, the printer supports mixed capacities up to the 1GB maximum across both slots.

How can I verify the new module is recognised at the correct speed after fitting it?

Print a configuration page from the Phaser 8560 control panel; the memory section lists total installed RAM and the detected speed.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.