Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green DDR3 DIMM sticks without heat spreaders

Computer Memory Solutions

Computer Memory Solutions 8GB (2x4GB) DDR3 1333MHz PC3-10600 CL9 1.5V Non-ECC DIMM

SKU CH-5594-S0H63

8GB dual-channel DDR3 kit with two 4GB modules rated at 1333MHz CL9, validated for HP 6000 Pro desktop systems

  • Capacity8GB (2 x 4GB)
  • Type240-Pin DDR3 SDRAM
  • SpeedDDR3 1333 (PC3 10600)
  • CAS LatencyCL9
  • Timing9-9-9
  • Voltage1.5V
  • 8GB dual-channel kit boosts multitasking headroom
  • 1333 MHz DDR3 speed matches system bus
  • CL9 1.5 V timing keeps latency low
  • Validated for HP 6000 Pro SFF and Microtower
  • Two 4 GB unbuffered DIMMs install in pairs

Kit Contents

This kit contains two 4GB DDR3 DIMMs for a total of 8GB. The modules run at 1333MHz with PC3-10600 rating and CL9 latency. They operate at 1.5V and are unbuffered non-ECC with a 2Rx8 rank. The 240-pin design matches the memory slots of the HP Business Desktop 6000 Pro in both Microtower and SFF form factors.

Who This Suits

This memory is intended for owners of the HP Business Desktop 6000 Pro who want to add 8GB using a matched pair. The system accepts up to 16GB across four slots and runs the memory bus at 1066MHz. Buyers who need ECC or registered modules for a server platform should look elsewhere. Systems that only support a lower maximum capacity will not be able to use the full kit.

Deciding Specification

The critical figure is the DDR3 1333 PC3-10600 rating with CL9 timing at 1.5V. The motherboard must accept 240-pin unbuffered non-ECC DIMMs and support a 2Rx8 organisation. If the board requires a different voltage, a different pin count, or ECC functionality, these modules will not work. The HP documentation confirms compatibility with this exact specification for the 6000 Pro series.

Kohokohdat

  • 8GB dual-channel kit boosts multitasking headroom
  • 1333 MHz DDR3 speed matches system bus
  • CL9 1.5 V timing keeps latency low
  • Validated for HP 6000 Pro SFF and Microtower
  • Two 4 GB unbuffered DIMMs install in pairs

Tekniset tiedot

BrandComputer Memory Solutions
ModelCM5126410600DIMM
Capacity8GB (2 x 4GB)
Type240-Pin DDR3 SDRAM
SpeedDDR3 1333 (PC3 10600)
CAS LatencyCL9
Timing9-9-9
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor Brand Chipset
Heat SpreaderNo
Compatible SystemHp Business Desktop 6000 Pro (Sff) (Microtower
Package Content2 Memory RAM Sticks

Kysymyksiä tästä tuotteesta

Does my HP 6000 Pro desktop need a 64-bit operating system to use the full 8 GB from this kit?

Yes, the system documentation states that maximum memory configurations require a 64-bit operating system; otherwise the recognised memory may be reduced to 3.5 GB or less.

Will these DDR3-1333 modules run at their rated 1333 MHz speed in my HP 6000 Pro?

The system supports DDR3-1333 modules, but HP specifies that the memory bus runs at 1066 MHz, so the kit will operate at the lower bus speed.

How can I confirm the kit is running in dual-channel mode after installation?

Install the two 4 GB sticks as a matched pair in the correct slots; the BIOS or operating system should then report 8 GB total with dual-channel operation active.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.