Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green 184-pin DDR1 DIMM sticks in a pair

Computer Memory Solutions

Computer Memory Solutions CM128643200DIMM 2GB (2x1GB) DDR1 400MHz CL3 184-pin DIMM memory upgrade

SKU CH-MXT7-TWGTA

Two 1 GB DDR1 DIMMs running at 400 MHz CL3 for Dell Dimension 2400, 2400C and 2400N systems

  • Capacity2GB (2 x 1GB)
  • Type184-Pin DDR SDRAM
  • SpeedDDR 400 (PC 3200)
  • CAS LatencyCL3
  • Timing3-3-3
  • Voltage2.6V
  • Guaranteed Dell Dimension 2400 compatibility from a trusted brand
  • 2GB total capacity in a matched 2 x 1GB kit for dual-channel performance
  • DDR1 400 MHz CL3 timing delivers responsive legacy system operation
  • 184-pin unbuffered non-ECC DIMM installs directly into existing slots
  • Major-brand chips at 2.6 V ensure stable, reliable operation

Dell Dimension 2400 series memory upgrade

This two-module kit provides 2 GB of DDR1 memory for Dell Dimension 2400, 2400C and 2400N desktops. Each stick delivers 1 GB over an 184-pin unbuffered DIMM interface. The set runs at 400 MHz with CL3 latency and 2.6 V operation. It is intended for owners of these specific legacy systems who need a straightforward capacity increase.

Thermals and power in daily use

The modules operate at the standard 2.6 V for DDR1 without a heat spreader. Power draw stays within the original platform envelope, so the existing chassis airflow handles thermals without extra noise. No active cooling or voltage tuning is required for stable operation at the rated 3-3-3 timings.

Replacing older DIMMs in these chassis

This kit replaces lower-capacity PC3200 DIMMs or fills empty slots on the supported Dimension models. The upgrade is worthwhile when the system currently runs with less than the maximum supported memory and the workload benefits from the extra 2 GB. It does not suit builds that require ECC, registered modules or speeds beyond DDR1 400 MHz.

Kohokohdat

  • Guaranteed Dell Dimension 2400 compatibility from a trusted brand
  • 2GB total capacity in a matched 2 x 1GB kit for dual-channel performance
  • DDR1 400 MHz CL3 timing delivers responsive legacy system operation
  • 184-pin unbuffered non-ECC DIMM installs directly into existing slots
  • Major-brand chips at 2.6 V ensure stable, reliable operation

Tekniset tiedot

BrandComputer Memory Solutions
ModelCM128643200DIMM
Capacity2GB (2 x 1GB)
Type184-Pin DDR SDRAM
SpeedDDR 400 (PC 3200)
CAS LatencyCL3
Timing3-3-3
Voltage2.6V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor Brand Chipset
Heat SpreaderNo
Compatible SystemDell Dimension 2400, 2400C, 2400N
Package Content2 Memory RAM Sticks

Kysymyksiä tästä tuotteesta

How do I install the 184-pin DDR1 DIMMs in a Dell Dimension 2400, and which step is most often missed?

Power off and unplug the system, open the case, align each module's notch with the slot key, press down firmly until both side clips click, then verify both sticks are fully seated before closing the case.

What maintenance or replacement will the 2GB DDR1 kit need over time?

No scheduled maintenance is required; if a module fails, replace the faulty 1GB stick with another PC3200 CL3 184-pin unbuffered non-ECC DIMM.

What limit appears first when the memory runs at 400 MHz under sustained load?

The CL3 3-3-3 timing at 2.6V sets the latency floor; bandwidth and stability are bounded by the DDR1 400 MHz specification.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.