Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Spool of bright yellow 3D printer filament, 2.85mm diameter, 750g net weight

E3D Online

E3D Online spoolWorks EDGE Filament 2.85mm 750g Limey Lime29 3d printers accessory

SKU CH-7Z7E-WH8AK

A recyclable PETG-based filament combining ABS toughness with PLA ease of use, low warp, strong layer adhesion and clean breakaway support pairing in 2.85 mm, 750 g lime yellow

  • ColorYellow
  • TypeFilament
  • Easy printing with no unpleasant fumes or odours
  • Strong, tough material with a naturally glossy finish
  • Low warp for accurate overhangs and tight bridges
  • Adheres to beds with just a little gluestick
  • Pairs with Scaffold support for clean breakaway

Filament Diameter and Weight

E3D Online spoolWorks EDGE is a PETG-based filament supplied as a 2.85 mm spool weighing 750 g in the Limey Lime29 colour. It is engineered for makers who want a strong, stiff material that prints with low warp and minimal odour.

Who This Suits and Who Should Look Elsewhere

It suits users printing functional parts that need high layer adhesion and toughness comparable to ABS but with easier bed adhesion using only a light gluestick coating. It is not for printers that cannot accept 2.85 mm stock, nor for applications requiring flexible, high-temperature or water-soluble filaments.

Recyclable PETG-Based Composition

The filament uses a modified PETG formulation that is widely recyclable while delivering exceptional resilience and a naturally glossy finish. This single material choice determines whether the mechanical properties and environmental profile match the project requirements.

Kohokohdat

  • Easy printing with no unpleasant fumes or odours
  • Strong, tough material with a naturally glossy finish
  • Low warp for accurate overhangs and tight bridges
  • Adheres to beds with just a little gluestick
  • Pairs with Scaffold support for clean breakaway

Tekniset tiedot

BrandE3D
ModelEdge
ColorYellow
TypeFilament

Kysymyksiä tästä tuotteesta

How does the 2.85 mm diameter behave once it is loaded into a real machine?

The 2.85 mm filament feeds smoothly through standard Bowden or direct-drive extruders and melts consistently for reliable layer bonding.

What interface or standard governs this spool, and what does it limit in practice?

The spool follows the common 2.85 mm diameter standard used by many desktop printers, so it fits any machine designed for that size.

What does the 750 g spool physically need to fit or mount on a printer?

The 750 g spool mounts on any standard filament holder that accepts a typical hub diameter and spool width.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.