Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black 3D printer filament spool 2.85mm 750g

E3D Online

E3D Online spoolWorks EDGE Filament 2.85mm 750g Very Black30 3d printers accessory

SKU CH-7K1C-BE08Y

A recyclable PETG-based filament combining ABS-like toughness with easy printing, low warp, strong layer adhesion, and reliable bed adhesion using gluestick

  • ColorBlack
  • TypeFilament
  • Recyclable PETG-based material reduces environmental impact
  • Easy printing with no unpleasant fumes or odours
  • Strong, tough and naturally glossy finish for durable parts
  • Adheres to bed surfaces with just a little gluestick
  • Pairs with Scaffold support for reliable adhesion and clean breakaway

E3D spoolWorks EDGE Filament 2.85mm 750g

This PETG-based filament is developed in-house by E3D as part of the SpoolWorks range. It combines the toughness and resilience of ABS with PLA’s ease of use for superior processing properties. The material offers strong layer adhesion at a molecular level, making parts nearly as strong between layers as across them. It is widely recyclable and prints with no unpleasant fumes or odors.

Makers needing tough, low-warp PETG

Users who require a filament that adheres effectively to bed surfaces with only a little gluestick will benefit from this formulation. The material achieves accurate overhangs and tight bridges thanks to carefully managed viscosity and melt strength. Buyers who need a different diameter or a non-PETG material such as pure PLA or ABS should look at alternative filaments.

2.85mm diameter 750g spool Very Black30 colour

The filament is supplied on a 750g spool with a 2.85mm diameter in the Very Black30 colour variant. This specific diameter suits printers designed for 2.85mm feedstock and must match the printer’s extrusion system. The glossy black finish provides a naturally shiny appearance on printed parts without additional processing.

Kohokohdat

  • Recyclable PETG-based material reduces environmental impact
  • Easy printing with no unpleasant fumes or odours
  • Strong, tough and naturally glossy finish for durable parts
  • Adheres to bed surfaces with just a little gluestick
  • Pairs with Scaffold support for reliable adhesion and clean breakaway

Tekniset tiedot

BrandE3D
ModelEdge
ColorBlack
TypeFilament

Kysymyksiä tästä tuotteesta

What is the filament diameter and spool weight for the E3D spoolWorks EDGE Very Black30?

The filament diameter is 2.85mm and the spool weight is 750g.

What bed surface preparation does the EDGE filament require for effective adhesion?

It adheres effectively to bed surfaces with just a little bit of gluestick.

How is the EDGE filament installed and what step is commonly missed?

Load the 2.85mm filament into the extruder and apply a thin layer of gluestick to the bed; users often skip the gluestick step.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.