Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green rectangular circuit board with a 40-pin IDE connector, a SATA port and a 4-pin power socket

EN-Labs

EN-Labs 11-001-171 3.5" IDE/PATA to SATA adapter

SKU CH-TG3S-GYNWV

Converts a 3.5 inch IDE drive to SATA with a 40 pin port and Molex power cable included

  • SpecificationsConverts Parallel ATA to Serial ATA Supports ATA 100/133 Fit
  • FeaturesIDE to SATA Adapter ("Convert IDE Hard Drive to SATAHard Dri
  • Package Contents1 x bridge board 1 x Molex power cable
  • Connect IDE drives to SATA motherboards using the 40-pin converter bridge
  • Supports ATA 66/100/133 speeds for broad IDE drive compatibility
  • Works with IDE drives up to 1000GB capacity for storage upgrades
  • Plug-and-play operation with no drivers needed across DOS, Windows 98 through 7 and Linux
  • Includes Molex power cable so no extra power supply is required

Bridge board for 3.5-inch IDE drives

This adapter board lets you connect a 3.5-inch Parallel ATA hard drive or optical drive to a Serial ATA motherboard header. It is intended for desktop users who want to keep an existing IDE device when upgrading to a board that only offers SATA ports. The package includes the bridge board and a Molex power cable.

Practical limits of the Parallel ATA interface

The converter supports ATA 66, 100 and 133 MB/s transfer modes and works with drives up to 1000 GB. The drive jumper must be set to Master; Cable Select or Slave settings will prevent operation. The unit is not hot-swappable and requires a system restart when the drive is changed.

Single specification that decides fit

One 40-pin IDE connector and one SATA 7-pin connector are provided on the board. If your motherboard lacks a free SATA port or your drive does not have a standard 40-pin interface, this adapter cannot be used.

Kohokohdat

  • Connect IDE drives to SATA motherboards using the 40-pin converter bridge
  • Supports ATA 66/100/133 speeds for broad IDE drive compatibility
  • Works with IDE drives up to 1000GB capacity for storage upgrades
  • Plug-and-play operation with no drivers needed across DOS, Windows 98 through 7 and Linux
  • Includes Molex power cable so no extra power supply is required

Tekniset tiedot

BrandEn-Labs
Model11-001-171
SpecificationsConverts Parallel ATA to Serial ATA
Supports ATA 100/133
Fit for 3.5" IDE HDD DVD.
One 40pin IDE port.
One Serial ATA port.
One 4pin power connector
FeaturesIDE to SATA Adapter ("Convert IDE Hard Drive to SATAHard Drive")
Connect a IDE hard drive to you SATA motherboard with this IDE to SATA Adapter
Turn your IDE hard drive into SATA interface hard drive
Package Contents1 x bridge board
1 x Molex power cable

Kysymyksiä tästä tuotteesta

Which version of the EN-Labs 11-001-171 adapter should I choose for a 3.5 inch IDE hard drive?

The single model 11-001-171 converts a 3.5 inch 40-pin IDE drive to a SATA connection. It includes one bridge board and a Molex power cable, so no other version is needed.

What does the 133 MB/s figure mean when the adapter is installed in a real system?

The adapter supports IDE modes up to 133 MB/s, but actual throughput will be limited by the drive's own speed and the motherboard's SATA controller.

Which interface standard does the 40-pin IDE port use, and what does it cap in practice?

The 40-pin port handles Parallel ATA at up to 133 MB/s; the SATA side connects to a standard Serial ATA motherboard header.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.