Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Silver 120mm square case fan 38mm thick with metal finger guard grille

EZDIY-FAB

EZDIY-FAB 120mm 200CFM 4000RPM 12V 4-Pin Molex Case Fan with Metal Guard

SKU CH-S42T-7J42B

Dual 120 mm fans deliver 200 CFM at 4000 RPM with metal guards for high-static-pressure cooling

  • Moves 200 CFM at 4000 RPM for extreme airflow
  • Dual ball bearing rated for long service life
  • 12 V 4-pin Molex connector fits standard PSU cables
  • 38 mm thick frame with metal finger guard included
  • Operates from 7 to 13.2 V for flexible speed control

120 mm 200 CFM dual-ball-bearing fan

This 120 mm by 38 mm DC fan moves 200 CFM at 4000 RPM using a dual ball bearing. It draws 1.4 A at 12 V with a 36 W input and connects through a standard 4-pin Molex power plug. The operating voltage range spans 7 to 13.2 V.

Suited for high-airflow server or mining rigs.

The 59 dBA maximum noise level makes this fan appropriate for server chassis, mining rigs or industrial ventilation where raw airflow matters more than acoustics. Builders who need a silent or low-noise environment should look at lower-speed alternatives. The metal finger guard adds safety in open-frame or high-traffic installations.

36 W power draw per fan at 12 V

Each unit consumes 36 W at the rated 12 V, so the power supply must deliver enough 12 V current for every fan installed. The 4-pin Molex connector draws directly from the PSU without motherboard speed control. Verify that your PSU has sufficient Molex connectors and 12 V capacity before adding multiple fans.

Kohokohdat

  • Moves 200 CFM at 4000 RPM for extreme airflow
  • Dual ball bearing rated for long service life
  • 12 V 4-pin Molex connector fits standard PSU cables
  • 38 mm thick frame with metal finger guard included
  • Operates from 7 to 13.2 V for flexible speed control

Tekniset tiedot

Tälle tuotteelle ei ole vielä julkaistu teknisiä tietoja.

Kysymyksiä tästä tuotteesta

Does my case have the 120mm x 38mm mounting space and a free 4-pin Molex connector for this fan?

The fan measures 120mm x 120mm x 38mm and draws 1.4A at 12V through a 4-pin Molex connector, so your case needs that clearance and a spare Molex lead from the power supply.

Will the 4000 RPM speed and 59dBA noise overwhelm older components on the same Molex rail?

Each fan pulls up to 3.0A peak, so a shared Molex rail must handle that surge; the 59dBA output is loud, so isolate vibration with the included metal grills and screws to protect aging drives.

How can I confirm the fans are spinning at the rated 4000 RPM after installation?

Connect the 4-pin Molex, power on, and check BIOS or fan-control software for a reading near 4000 RPM; the strong airflow and audible 59dBA hum also confirm full-speed operation.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.