Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black soft-tube water-cooling kit with three 1m tubes, ten compression fittings, two 90° elbows, a mini M2M adapter and a tube cutter

FormulaMod

FormulaMod Soft Tube Fitting Kit 10x13mm Black G1/4 Compression Combo

SKU CH-VMSB-4FT3W

Complete G1/4 water-cooling kit with three metres of 10x13mm soft tubing, ten compression fittings, two 90° elbows, a mini male-to-male joiner and a tube cutter

  • TypeCombo Kit
  • ColorBlack

Color Black

  • Complete water-cooling kit with tubing, fittings and cutter included
  • 10 mm inner and 13 mm outer diameter soft tubing for secure G1/4 compression seals
  • Three one-metre tubes, ten straight fittings, two 90° elbows and one mini M2M adapter supplied
  • Integrated tube cutter enables clean, square cuts for leak-free assembly
  • Compatible with new builds and upgrades using standard G1/4 threaded components

Complete Soft-Tube Kit for Custom Loops

This FormulaMod bundle supplies 10x13 mm soft tubing, ten G1/4 compression fittings, two 90° elbows, one mini male-to-male joiner and a dedicated tube cutter. Everything needed to assemble or refresh a water-cooling loop arrives in a single package. The kit suits both first-time builders and experienced modders updating an existing system.

Leak-Free Sealing With Standard G1/4 Threads

Compression fittings grip the 10x13 mm tube evenly around its circumference, creating a reliable seal on every G1/4 port without specialised tools. The included cutter produces clean, square ends that seat fully in each fitting, reducing the risk of coolant loss. No pump noise or thermal data apply because the kit contains no active components.

Pre-Cut Lengths and Angled Fittings Simplify Routing

Three one-metre tube sections let you trim exact runs for CPU blocks, radiators and reservoirs without waste. The 90° elbows enable tight bends around motherboard heatsinks or GPU back-plates where straight fittings would kink the tube. The mini joiner connects two fittings directly for compact bridge sections. No software, lighting or monitoring features are included.

Kohokohdat

  • Complete water-cooling kit with tubing, fittings and cutter included
  • 10 mm inner and 13 mm outer diameter soft tubing for secure G1/4 compression seals
  • Three one-metre tubes, ten straight fittings, two 90° elbows and one mini M2M adapter supplied
  • Integrated tube cutter enables clean, square cuts for leak-free assembly
  • Compatible with new builds and upgrades using standard G1/4 threaded components

Tekniset tiedot

TypeCombo Kit
ColorBlack

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How do I install the 10x13mm soft tubing onto the G1/4 compression fittings without leaks?

Cut the tube square with the included cutter, slide the compression nut and olive onto the tube, push the tube fully onto the fitting barb until it seats against the internal stop, then hand-tighten the nut plus a quarter turn with a spanner; the step most people miss is not pushing the tube past the olive far enough to hit the stop.

Which parts of this kit will need replacement after extended use?

The 10x13mm soft tubing can harden or discolour over time and should be inspected annually; the EPDM O-rings inside the 10 compression fittings, two 90° fittings and one mini M2M fitting may also lose elasticity and are the typical service items.

What is the first limit I will hit when running this loop continuously under load?

The 10x13mm tubing has a lower burst-pressure rating than hard tube, so sustained high coolant temperatures combined with pump pressure will reach the tube's pressure-temperature limit before the G1/4 compression fittings or 90° elbows become restrictive.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.