Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Twenty-two small blue aluminium heatsinks with adhesive backing, each nine by nine by twelve millimetres

Grwibeou

Grwibeou 22pcs Blue Aluminum Chipset Heatsink Kit 9x9x12mm

SKU CH-7QES-1A35M

Set of 22 blue aluminum heatsinks with adhesive tape for passive cooling of stepper motor drivers

  • TypeHeatsinks only
  • CompatibilitySouth and North Bridge chips
  • Heatsink MaterialAluminum
  • Passive cooling for stepper drivers TMC2130 TMC2100 A4988 DRV8825 TMC2208
  • Pre-applied thermal adhesive tape simplifies installation on modules
  • 22 blue aluminium heatsinks included for multiple board builds
  • Compact 9 x 9 x 12 mm size fits tight component spacing
  • Lightweight at 0.04 oz each adds minimal mass to assemblies

22-piece aluminum heatsink kit for stepper drivers

This set supplies twenty-two blue aluminum heatsinks sized 9 by 9 by 12 millimetres for passive cooling of stepper motor driver modules. It targets builders of 3D printers and CNC machines who need to dissipate heat from TMC2130, TMC2100, A4988, DRV8825 or TMC2208 chips without adding active airflow. Each piece weighs roughly .04 ounce and ships new.

Pre-applied thermal adhesive tape simplifies

Every heatsink carries a layer of thermal conductive adhesive tape on its base, so no separate paste or glue is required. The tape bonds directly to the driver IC once the protective liner is removed, cutting assembly time and ensuring consistent contact pressure across all twenty-two units. Stepper motor driver modules themselves are not included in the package.

Compact 9-millimetre footprint fits dense board

At .35 by .35 by .47 inch each, the heatsinks occupy minimal board real estate, allowing placement on tightly spaced driver modules common in 3D printer control boards. The low 12-millimetre height clears most enclosure lids and wiring looms while still providing a measurable thermal path to ambient air. Blue anodised finish resists corrosion and aids visual identification during maintenance.

Kohokohdat

  • Passive cooling for stepper drivers TMC2130 TMC2100 A4988 DRV8825 TMC2208
  • Pre-applied thermal adhesive tape simplifies installation on modules
  • 22 blue aluminium heatsinks included for multiple board builds
  • Compact 9 x 9 x 12 mm size fits tight component spacing
  • Lightweight at 0.04 oz each adds minimal mass to assemblies

Tekniset tiedot

TypeHeatsinks only
CompatibilitySouth and North Bridge chips
Heatsink MaterialAluminum

Kysymyksiä tästä tuotteesta

Will the adhesive tape on the 9mm x 9mm x 12mm heatsinks need replacing after long use?

The thermal conductive adhesive tape is pre-applied; if it loses grip over time, new thermal tape or paste can be used to re-secure the blue aluminum pieces.

What thermal limit appears first when these 1 gram heatsinks run continuously on stepper drivers?

Passive aluminum mass saturates quickly, so the heatsink temperature itself becomes the limiting factor before the driver throttles.

How much noise, heat or extra power do 22 of these blue aluminum heatsinks add when the printer runs all day?

They add zero noise and zero power draw; they simply spread heat from TMC2130, TMC2100, A4988, DRV8825 or TMC2208 modules into the surrounding air.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.