Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Five small rectangular blue OLED display boards with gold pins

Hosyond B011 0.96" OLED 128x64 I2C Blue 5 Pcs

SKU CH-CZ00-4GSJX

Pack of five 0.96″ OLED modules with 128×64 resolution, I²C interface, 3.3–5 V supply and SSD1306 driver for Arduino or Raspberry Pi projects

  • Self-luminous OLED needs no backlight for crisp text
  • 96 inch 128x64 resolution gives high pixel density
  • >160° viewing angle stays readable from the side
  • I²C interface uses only two I/O pins
  • 3V–5V logic works without level-shifting chips

Hosyond B011 0.96" OLED Display Pack

This pack contains five Hosyond B011 OLED modules, each with a 0.96 inch 128x64 pixel blue display driven by the SSD1306 controller. The I2C interface requires only two I/O pins and operates from 3.3V to 5V DC. Each board draws 0.04W during normal use and 0.08W with the full screen lit. They are aimed at makers building compact readouts for microcontroller projects.

Suits Arduino, Pi and MCU prototypes.

These displays suit hobbyists adding status screens to Arduino Nano, R3, Mega, Raspberry Pi, 51 MCU or STM32 projects. The 128x64 resolution and monochrome blue output limit them to text, icons and simple charts. Projects needing colour, video playback, touch input or larger viewing areas should choose a different display technology.

128x64 SSD1306 I2C resolution and interface

The single specification that decides fit is the 128x64 pixel SSD1306 panel driven over I2C. This resolution and bus define the wiring, library support and graphics memory available. Verify your host has two free I/O pins and can supply 3.3V or 5V before purchasing.

Kohokohdat

  • Self-luminous OLED needs no backlight for crisp text
  • 96 inch 128x64 resolution gives high pixel density
  • >160° viewing angle stays readable from the side
  • I²C interface uses only two I/O pins
  • 3V–5V logic works without level-shifting chips

Tekniset tiedot

BrandHosyond
Part NumberB011

Kysymyksiä tästä tuotteesta

How do I confirm the 0.96" OLED is working after wiring it to my Arduino?

Power the module at 3.3V–5V DC, run an I2C scanner to detect address 0x3C, then load a test sketch that fills the 128x64 pixel array; the blue self-luminous pixels should light without a backlight.

What comes in the pack and what extra parts are needed?

The box contains five 0.96" OLED modules with SSD1306 driver ICs in protective boxes; you must supply jumper wires, a 3.3V–5V microcontroller such as Arduino Nano, R3, Mega or Raspberry Pi, and a suitable library.

Which colour variant should I pick for best contrast in daylight?

Choose the blue version listed here; its self-luminous pixels give ultra-high contrast and a viewing angle greater than 160°, making small fonts easy to read even in bright conditions.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.