Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Three purple ESP32 boards with USB-C and matching breakout shields

KEHIPI

KEHIPI 3 Sets ESP32 ESP-WROOM-32 38Pin Development Board Type C with Breakout Shield

SKU CH-4S68-WD640

Three ESP32 development boards with USB-C and dual-layer breakout shields expand each GPIO pin to two connections

  • Three boards per pack for parallel prototyping
  • USB-C and Micro-USB power options on each board
  • CP2102 USB-UART chip for direct serial programming
  • 38-pin breakout shields expand each GPIO to two pins
  • Dual-core ESP32 with 2.4 GHz Wi-Fi and Bluetooth

Three ESP32 boards with Type C and shields

This pack contains three ESP32 development boards built around the ESP‑WROOM‑32 module. Each board uses a CP2102 USB‑C interface for power and programming and exposes 38 pins. Integrated 2.4 GHz Wi‑Fi and Bluetooth dual‑core radios support AP, STA and AP+STA modes for wireless IoT projects.

Makers adding wireless to compact prototypes

The 38‑pin narrow form factor suits builders who need a small footprint and duplicated GPIO via the included breakout shields. It does not suit developers who require the 30‑pin variant or boards without the expansion header, because the shields only fit this exact pin count.

38‑pin narrow ESP32 with CP2102 USB‑C

The decisive specification is the 38‑pin narrow ESP‑WROOM‑32 layout paired with a CP2102 USB‑C interface; the breakout shields only connect to this pin arrangement, so code and wiring must target this exact board geometry.

Kohokohdat

  • Three boards per pack for parallel prototyping
  • USB-C and Micro-USB power options on each board
  • CP2102 USB-UART chip for direct serial programming
  • 38-pin breakout shields expand each GPIO to two pins
  • Dual-core ESP32 with 2.4 GHz Wi-Fi and Bluetooth

Tekniset tiedot

BrandAITRIP

Kysymyksiä tästä tuotteesta

Does the board need any external programmer or will the on-board CP2102 handle flashing over the Type-C port?

The CP2102 USB-to-UART bridge is built onto the 38-pin development board, so flashing firmware over the Type-C connector requires no separate programmer.

Can the 38-pin breakout shield be used with the 30-pin ESP32 boards I already own?

The shield is designed only for 38-pin ESP32 core boards; it will not fit or connect correctly to 30-pin variants.

How can I confirm the Wi-Fi and Bluetooth radios are active after powering the board?

Upload a sketch that initialises Wi-Fi in AP, STA or AP+STA mode and Bluetooth, then watch the serial monitor for connection logs or scan for the advertised network.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.