Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Three green ESP32 expansion boards with 38-pin headers and USB-C connectors

KEHIPI

KEHIPI 3PCS 38PINS ESP32 Development Board Type-C CP2102

SKU CH-6P0E-S6YPH

Three ESP32 expansion boards with 38-pin headers and Type-C CP2102 interfaces for compatible WROOM and WROVER modules

  • 3-pack gives spare boards for parallel projects
  • 38-pin layout matches wide ESP32 modules like WROOM-32D and WROVER
  • USB Type-C port with CP2102 bridge for simple flashing and power
  • Supports Lua, FreeRTOS and LWIP for rapid IoT firmware development
  • Works in AP, STA and AP+STA modes for flexible Wi-Fi networking

38-Pin ESP32 Expansion Board Pack

This pack contains three 38-pin expansion boards built for ESP32 development modules. Each board uses a CP2102 USB-to-UART bridge and offers a Type-C or Micro USB interface. The extended bottom-board layout matches the ESP32-DevKitC-32 form factor and supports Lua programming with LWIP and FreeRTOS in AP, STA and AP+STA modes.

Makers needing multiple ESP32 breakout boards

Suited for developers who want three ready-to-use 38-pin carrier boards for rapid prototyping or classroom sets. Not for buyers who need a different pin count, a single-unit pack, or an on-board ESP32 module included in the package.

38-pin compatibility constraint

The boards only accept the listed 38-pin wide-version modules such as ESP32-WROOM-32S, 32E, 32D, 32U, WROVER and WROVER-IB. Verify your module against the approved ASINs B09LMBX8WH, B09KRHNC6Z, B08HMJ1X6W, B088QVQCTL and B086YS4Z3F before ordering.

Kohokohdat

  • 3-pack gives spare boards for parallel projects
  • 38-pin layout matches wide ESP32 modules like WROOM-32D and WROVER
  • USB Type-C port with CP2102 bridge for simple flashing and power
  • Supports Lua, FreeRTOS and LWIP for rapid IoT firmware development
  • Works in AP, STA and AP+STA modes for flexible Wi-Fi networking

Tekniset tiedot

BrandAITRIP

Kysymyksiä tästä tuotteesta

What module pin count does this 38-pin expansion board require?

The board only accepts ESP32 modules with a 38-pin wide footprint such as the WROOM-32D, WROOM-32U or WROVER variants listed in the compatibility notice.

How do I connect the board to a computer for programming?

Plug a USB Type-C cable into the on-board CP2102 USB-to-UART bridge; the board then appears as a serial port for flashing firmware.

When should I replace the CP2102 USB-to-UART bridge on this board?

Replace it only if the device no longer enumerates as a COM port or shows persistent upload failures across multiple cables and hosts.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.