Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Small spool of translucent 2.85 mm filament in light cardboard box

Lay Filaments

Lay Filaments ETHY-LAY Dissolvable Support Filament 2.85mm 0.10kg

SKU CH-G1ZQ-3JXCG

Dissolvable support filament that prints at 165 °C without a heated bed and dissolves in alcohol for water-sensitive materials

  • Dissolves in alcohol, avoiding water-sensitive filament damage
  • Low 165 °C print temperature reduces warping risk
  • No heated bed needed, simplifying printer setup
  • Alternative to PVA and HIPS for support structures
  • 85 mm diameter suits compatible 3D printers

Dissolvable Support for Water-Sensitive Prints

ETHY-LAY is a dissolvable support filament from the Lay-Away series designed for dual-extrusion 3D printing. It dissolves in alcohol rather than water or D-Limonene, making it suitable for primary materials that cannot tolerate moisture exposure. The filament diameter is 2.85 mm and the spool weighs 0.10 kg. It prints at a low temperature of 165 °C without requiring a heated bed.

Replaces PVA and HIPS When Water Contact Is

This filament serves as an alternative to PVA and HIPS support materials for prints where the model material degrades or warps in water. The switch is worthwhile when your primary filament demands a dry support removal process or when a heated bed is unavailable. It is not suited for single-extrusion setups or for users who prefer water-soluble supports for convenience.

Low-Temperature Extrusion Reduces Heat Stress

Because ETHY-LAY extrudes at 165 °C, it places less thermal demand on the hotend during long support-printing sessions. The absence of a heated bed requirement simplifies printer preparation and reduces overall energy draw during extended builds. Consistent diameter control helps maintain steady flow rates across large support structures.

Kohokohdat

  • Dissolves in alcohol, avoiding water-sensitive filament damage
  • Low 165 °C print temperature reduces warping risk
  • No heated bed needed, simplifying printer setup
  • Alternative to PVA and HIPS for support structures
  • 85 mm diameter suits compatible 3D printers

Tekniset tiedot

BrandLay Filaments

Kysymyksiä tästä tuotteesta

Will the 2.85 mm diameter work with my 3.0 mm filament drive?

The filament is manufactured to 2.85 mm, which is the standard tolerance for printers specified for 3.0 mm material, so it feeds correctly in those systems.

What printing temperature and bed setting should I use for ETHY-LAY?

Extrude at 165 °C and leave the heated bed off; the material is designed to print at low temperature without bed adhesion aids.

How do I remove the support material after printing?

Submerge the finished part in alcohol — ethanol or isopropyl — and the ETHY-LAY supports will dissolve, unlike PVA or HIPS which need water or limonene.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.