Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
4.3 inch IPS touch display with toughened glass panel and ribbon cable

LORDWORLD

LORDWORLD 4.3inch DSI Touch Display 800×480 IPS development board

SKU CH-AE2C-SEHHJ

A 4.3 inch IPS touchscreen with 800×480 resolution and 5‑point capacitive touch connects via DSI for up to 60 Hz refresh on Raspberry Pi boards

  • 3 inch IPS panel gives 800 × 480 pixel clarity
  • 5 point capacitive touch on 6H toughened glass
  • Direct DSI drive reaches 60 Hz refresh
  • Works with Raspberry Pi 4B 3B+ 3A+ 3B 2B B+ A+
  • Development resources and manual included for quick start

4.3-inch DSI Touch Display for Raspberry Pi

This 4.3 inch IPS panel connects directly to the Raspberry Pi DSI port and delivers an 800 × 480 hardware resolution. It is intended for developers and hobbyists building embedded interfaces, kiosks or portable projects that need a compact touchscreen. The board includes a 5-point capacitive touch layer on toughened glass rated to 6H hardness. Electronic development resources and a manual are supplied for integration.

DSI interface limits and cable requirements

The display is driven through the Raspberry Pi DSI port at a refresh rate up to 60Hz. Compatible models include Pi 4B, 3B+, 3A+, 3B, 2B, B+, A+ and some CM3, CM3+ and CM4 expansion boards. Certain Compute Module carrier boards require an external 15cm DSI cable, which is not included, to reach the connector. The DSI bus bandwidth and the Pi GPU set the practical ceiling for resolution and frame rate.

Capacitive touch specification decides suitability

The single specification that determines fit is the 5-point capacitive touch controller on the 4.3 inch panel. Projects needing resistive input, glove operation or a different touch-point count will not be served by this board. Buyers who need a larger display area, higher pixel density or a non-touch variant should look elsewhere.

Kohokohdat

  • 3 inch IPS panel gives 800 × 480 pixel clarity
  • 5 point capacitive touch on 6H toughened glass
  • Direct DSI drive reaches 60 Hz refresh
  • Works with Raspberry Pi 4B 3B+ 3A+ 3B 2B B+ A+
  • Development resources and manual included for quick start

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

Which Raspberry Pi models does the 4.3inch DSI touch display support?

The board works with Pi 4B, 3B+, 3A+, 3B, 2B, B+, A+ and CM3, CM3+, CM4 modules; some CM expansion boards need the optional 15 cm DSI cable.

What does the 800 × 480 resolution mean when the panel is driven from the Pi DSI port?

The display shows 800 × 480 pixels at up to 60 Hz refresh, giving a crisp 4.3 inch IPS image directly from the Raspberry Pi’s DSI interface.

How does the DSI connection limit the touch panel in practice?

The 5‑point capacitive touch and 6H hardened glass are driven over the same DSI link, so all touch data travels through the Pi’s native display port without extra USB or GPIO wiring.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.