Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Small green circuit board with a 16x2 character LCD showing white text on blue background and a four pin header

LORDWORLD

LORDWORLD LCD1602 I2C Display Module 16x2 White Blue 3.3V 5V

SKU CH-B8KJ-PTTRM

A 16x2 character LCD with I2C interface needs only two signal pins and runs on 3.3V or 5V for Raspberry Pi, ESP32 and Arduino projects

  • 16x2 character display with white text on blue background
  • I2C interface uses only two signal pins
  • AiP31068 controller supports 3.3 V and 5 V operation
  • Compatible with Raspberry Pi, Jetson Nano, ESP32 and Arduino
  • Online manual and example code included for quick setup

Compact 16x2 I2C Character Display

This LORDWORLD module uses an LCD1602 panel with an AiP31068 controller and a built-in I2C interface that needs only two signal lines. It operates at either 3.3 V or 5 V and shows 16 characters by 2 rows with a white-on-blue background. The board is designed for direct connection to popular development platforms.

Suited for GPIO-limited boards.

Makers using Raspberry Pi, Jetson Nano, ESP32 or Arduino boards that have few free pins will benefit from the two-wire interface. Projects needing colour graphics, touch input, or higher character counts should look at alternative display types.

Online examples speed up first integration

The supplier provides code samples and a manual covering Raspberry Pi, Jetson Nano, ESP32 and Arduino environments. These resources let developers initialise the display and print text without writing low-level driver code from scratch.

Kohokohdat

  • 16x2 character display with white text on blue background
  • I2C interface uses only two signal pins
  • AiP31068 controller supports 3.3 V and 5 V operation
  • Compatible with Raspberry Pi, Jetson Nano, ESP32 and Arduino
  • Online manual and example code included for quick setup

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

Which development board do I need to provide the I2C bus and 3.3 V or 5 V supply for this module?

The module works with any board that exposes an I2C bus at 3.3 V or 5 V, including Raspberry Pi 4B, 3B+, Zero W, Pico, Jetson Nano or ESP32.

Will the AiP31068 controller on this display work with 5 V logic on my older Arduino Uno?

Yes, the AiP31068 controller is compatible with both 3.3 V and 5 V operating voltage, so it can be driven directly from a 5 V Arduino Uno.

How can I verify the LCD1602 panel and I2C interface are functioning after wiring?

Run the supplied example sketch for your platform; the 16×2 white-on-blue panel should show the test text and the I2C address scan should list the controller.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.