Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with gold PCIe edge connector and M.2 E-key slot

LORDWORLD

LORDWORLD PCIE to M.2 E Key Adapter HAT+ Board

SKU CH-9YJS-PCC5D

Converts a PCIe slot to an M.2 E-Key interface for WiFi and Bluetooth modules, not NVMe SSDs

  • Adds Wi-Fi and Bluetooth via any PCIe x1/x4/x8/x16 slot
  • Converts PCIe to M.2 E-Key for wireless cards only
  • Gold-plated connectors and onboard regulation for stable signals
  • Mount vertically or horizontally to fit tight chassis space
  • Plug-and-play setup with manual and online Wiki guide

PCIe-to-M.2 E-Key adapter for wireless modules

This adapter converts a standard PCIe slot into an M.2 E-Key interface so you can add a Wi-Fi or Bluetooth card to a desktop or industrial motherboard. It is not compatible with M-Key NVMe SSDs and requires a system BIOS that supports E-Key devices. Builders wanting to add NVMe storage should look elsewhere.

Thermals noise and power draw in normal use

Gold-plated connectors and onboard voltage regulation deliver stable power and clean signal transmission to the wireless module. The passive design adds no fan noise and draws minimal power from the PCIe slot during typical operation. Installers must ensure the motherboard firmware recognises E-Key hardware before expecting full functionality.

Manual and online Wiki guide installation

A printed manual and an online Wiki provide step-by-step instructions for plug-and-play setup in either a vertical or horizontal orientation. These resources cover physical mounting and driver configuration so the wireless card is recognised by the operating system. No additional brackets, cables or software licences are included in the package.

Kohokohdat

  • Adds Wi-Fi and Bluetooth via any PCIe x1/x4/x8/x16 slot
  • Converts PCIe to M.2 E-Key for wireless cards only
  • Gold-plated connectors and onboard regulation for stable signals
  • Mount vertically or horizontally to fit tight chassis space
  • Plug-and-play setup with manual and online Wiki guide

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

How do I install the LORDWORLD PCIE to M.2 E Key Adapter HAT+ Board in a PCIe x16 slot?

Insert the board into any free PCIe x1/x4/x8/x16 slot, secure the M.2 E-Key WiFi/Bluetooth module with the mounting screw, and verify BIOS recognises the E-Key device before booting the OS.

What maintenance will the onboard voltage regulation need over time?

No scheduled maintenance is required; the gold-plated connectors and fixed voltage regulator are passive components, so only reseat the board if contact oxidation appears after years of service.

What thermal limit appears first when the E-Key wireless module runs at full throughput?

The module itself reaches its thermal throttle point before the adapter, because the HAT+ has no active cooling and relies on case airflow to dissipate heat from the onboard regulator.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.