Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Rectangular aluminium power supply unit with terminal block and voltage selector switch

myVolts

myVolts 1000W Switching Power Supply 53-58V AC 100-240V

SKU CH-MS7S-593GA

Converts AC 100-240 V to selectable DC 53-58 V at 1000 W with short-circuit, overload and over-voltage protection

  • TypeAT
  • Delivers up to 1000W for demanding projects
  • Selectable 53V to 58V DC output matches varied loads
  • Efficiency above .85 reduces heat and energy waste
  • Built-in short-circuit, overload and over-voltage protection safeguards equipment
  • Wide 100-240V AC input suits global mains supplies

1000W Switching Supply for Industrial Projects

This myVolts unit converts AC 100-120V or 200-240V input into adjustable DC output from 53V to 58V at up to 1000W. It suits CCTV installations, 3D printers, LED strips and custom computer projects that need a high-power DC source. Professional installation by a qualified electrician is recommended because no wiring, switch or mounting screws are included.

Sustained Load Behaviour and Protection

Efficiency exceeds 0.85 at 230VAC input and 25°C, and every unit passes a 100% full-load burn-in test. Overload protection triggers between 110% and 150% of rated power, shutting down the output until the fault clears and auto-recovery resumes operation. Short-circuit and over-voltage protections also guard connected equipment during continuous use.

Input Voltage Selection and Environmental Limits

A manual selector sets the supply for either 100-120VAC or 200-240VAC at 50-60Hz; the correct range must be chosen before powering on. The aluminium-cased unit operates from -20°C to +60°C at 20-90% RH and can be stored from -40°C to +85°C at 10-95% RH. CE and RoHS compliance is declared for the design.

Kohokohdat

  • Delivers up to 1000W for demanding projects
  • Selectable 53V to 58V DC output matches varied loads
  • Efficiency above .85 reduces heat and energy waste
  • Built-in short-circuit, overload and over-voltage protection safeguards equipment
  • Wide 100-240V AC input suits global mains supplies

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

How much heat and noise should I expect when this 1000 W supply runs continuously at full load?

The unit is rated for 85 % input efficiency at 230 VAC and 25 °C, so roughly 150 W becomes heat. It uses a passively cooled aluminium case with no fan, so operation is silent but the enclosure will become hot.

What cables or connectors must I already have to wire this supply into my project?

You need suitably rated input wires for L and N, plus DC output cables for +V and -V. The supply ships without any wiring, on/off switch or mounting screws.

Will the adjustable ±2 V output let me match the 54 V rail on my older LED strips without modification?

Yes. The +V ADJ trimmer shifts the output between 53 V and 58 V, so you can set exactly 54 V to suit existing 54 V strips.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.