Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Silver 2U modular mining PSU with ten 6-pin connectors

myVolts

myVolts 1800W 2U Modular Mining PSU 10x6Pin

SKU CH-67WR-VX6ZJ

Modular 1800 W AT power supply with ten 6-pin connectors and 95 % conversion efficiency

  • TypeAT
  • 1800W output powers up to 10 mining devices simultaneously
  • 95% conversion efficiency lowers electricity costs versus typical passive PFC units
  • 10 six-pin connectors eliminate adapter clutter for GPU rigs
  • Automatic shutdown protects hardware during circuit faults or overheating
  • 100–240V AC input works on global mains without switching

Mining power supply with ten 6-pin connectors

The myVolts 1800 W modular PSU delivers up to 1800 watts of 12 V DC power from a 110–230 V AC source. It uses a 95 % conversion rate to keep electricity costs lower than passive PFC designs. An aluminium shell and all-copper transformer windings help the unit run cooler and last longer. Automatic shutdown triggers if a circuit fault or excessive internal temperature is detected.

Suitable for GPU mining rigs that need ten 6-pin

Miners powering Antminer S9, L3+, Z9 Mini or D3 units can connect each hash board directly without extra splitters. The 60 mm high-speed fan moves plenty of air, but the noise level is noticeable during full-load operation. Builds requiring more than ten connectors or any 8-pin or 12VHPWR leads cannot use this PSU as-is. Server installations needing redundant hot-swap modules should look at a different form factor.

Ten 6-pin outputs on a single 12 V rail

Every connector draws from the same 1800 W 12 V rail, so total load must stay within that limit. The 120 cm AC cord reaches most rack PDUs without an extension. Input voltage auto-ranges from 100 to 240 V, making the unit usable worldwide. Efficiency stays at or above 95 % across the load range, reducing waste heat and operating cost.

Kohokohdat

  • 1800W output powers up to 10 mining devices simultaneously
  • 95% conversion efficiency lowers electricity costs versus typical passive PFC units
  • 10 six-pin connectors eliminate adapter clutter for GPU rigs
  • Automatic shutdown protects hardware during circuit faults or overheating
  • 100–240V AC input works on global mains without switching

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

Which capacity should I pick for an 8-GPU mining rig?

The unit delivers 1800W on the 12V rail, matching the spec for eight GPUs with ten 6-pin connectors included.

What does the 95% conversion rate mean once the PSU is installed?

It indicates 95% or higher AC-to-DC efficiency, so less power is lost as heat and electricity costs are lower than typical passive PFC designs.

What does the 110-230V AC input range cap in practice?

The PSU auto-ranges between 110V and 230V mains, allowing worldwide use without a voltage switch while feeding a steady 12V DC output.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.