Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
White and black braided PSU cable extension kit with 24-pin, dual CPU and dual GPU connectors, 30cm length, includes cable combs

myVolts

myVolts 30cm PSU Cable Extension Kit 24-Pin 2x CPU 2x GPU WhiteBlack

SKU CH-4B8K-27YKP

A 30 cm sleeved extension kit with 24-pin, two CPU and two GPU cables in 18 AWG wire for tidy routing

  • TypeAT
  • Adds 30 cm reach to every power rail
  • 24-pin plus two 4+4-pin CPU and two 6+2-pin GPU connectors included
  • 18 AWG UL 1015 tinned copper cores inside high-density braided sleeve
  • Cable combs supplied for clean routing and a tidy interior
  • Choose from 17 colour options to match your build

Cable kit for custom PC builds

This extension kit bundles a 24-pin motherboard cable with two 8-pin CPU cables and two 8-pin GPU cables. It targets builders who want colour-matched sleeving without replacing their power supply. The set covers the main power paths for a typical high-end desktop configuration.

Flexible routing under continuous load

Each wire uses 18AWG UL 1015 tinned copper inside a high-density braided sleeve that stays pliable during long sessions. The construction resists heat buildup while keeping cables manageable for tight bends behind the motherboard tray. Included combs lock the wires into clean parallel runs that do not shift over time.

Verify connector counts before ordering

Check that your power supply provides the native 24-pin, dual 8-pin CPU and dual 8-pin PCIe outputs this kit extends. Builds with a single CPU power header or only one GPU power header will leave unused cables in the box. The 30cm length suits standard mid-tower layouts; measure your routing path if the case is unusually large or uses a rear-mounted PSU chamber.

Kohokohdat

  • Adds 30 cm reach to every power rail
  • 24-pin plus two 4+4-pin CPU and two 6+2-pin GPU connectors included
  • 18 AWG UL 1015 tinned copper cores inside high-density braided sleeve
  • Cable combs supplied for clean routing and a tidy interior
  • Choose from 17 colour options to match your build

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

How much heat or electrical resistance do the 18AWG UL 1015 tinned copper wires add when the system runs all day?

The 18AWG UL 1015 tinned copper conductors are rated for continuous operation at typical PSU loads; the 300 mm length keeps voltage drop negligible and the high-density braid dissipates heat normally, so daily use adds no measurable thermal load.

What existing power supply connectors are required for the 24-pin, dual 4+4-pin CPU and dual 6+2-pin GPU extensions to function?

Your PSU must provide a standard 24-pin ATX connector, two 4+4-pin EPS/CPU headers and two 6+2-pin PCIe headers; the extensions simply extend those existing cables without adding new rails.

Will the 30 cm length and stiff braided sleeve interfere with routing behind an older motherboard tray that has tight grommets?

The 300 mm extensions are highly flexible despite the dense sleeve, and the included cable combs let you train each run cleanly through narrow cut-outs common on older cases.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.