Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black dual PSU adapter cable with 24-pin main and two secondary connectors, 85cm long

myVolts

myVolts Dual PSU Adapter Practical Thin 24Pin 20+4 85cm 2000W

SKU CH-FEKG-M7XNJ

Connects two PSUs to one motherboard via 24-pin and 20+4-pin cables up to 2000W, with 85cm thin wiring

  • TypeAT
  • Combines two PSUs for extra power without upgrading hardware
  • Supports up to three units on one motherboard
  • 24-pin 20+4 connector works with 24-pin or 20-pin boards
  • Thin 85 cm cable keeps routing tidy inside the case
  • Rated for large supplies within 2000 W total capacity

Dual PSU adapter for 24-pin power

This adapter links two power supplies to a single motherboard through one main 24-pin female (20+4) connector and two secondary 24-pin female connectors. It targets desktop builders who need extra wattage for graphics cards without replacing their existing units. The thin cable design keeps routing tidy inside cramped cases.

Plug both PSUs into the adapter then into the board

Installation is a straight cable swap: seat the main 20+4 connector on the motherboard and attach each PSU to a secondary 24-pin plug. The thin wires bend easily but can snag on sharp drive-cage edges if pulled too tight. Verify that both power supplies are switched off before connecting to avoid a brief short between the units.

Check PSU wattage and motherboard pin count first

Confirm each power supply stays within the 2000 W combined limit stated for the adapter. Ensure the motherboard uses a standard 24-pin ATX socket so the 20+4 connector fits either 20-pin or 24-pin headers. The package contains only the cable; no mounting hardware or extra connectors are included.

Kohokohdat

  • Combines two PSUs for extra power without upgrading hardware
  • Supports up to three units on one motherboard
  • 24-pin 20+4 connector works with 24-pin or 20-pin boards
  • Thin 85 cm cable keeps routing tidy inside the case
  • Rated for large supplies within 2000 W total capacity

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

How can I verify the dual PSU adapter is delivering power correctly after connecting it?

After setup, the motherboard should receive power from both units through the 24-pin connectors and the system should boot without video-card throttling.

What comes in the package and which cables or connectors must be purchased separately?

The box contains one power cable with a 24-pin female (20+4) main connector and two 24-pin female secondary connectors; you supply the two power supplies and motherboard.

Which connector version should I choose for a motherboard that uses a 20-pin or 24-pin ATX socket?

The adapter’s 20+4-pin main connector fits both 20-pin and 24-pin motherboard sockets, so a single version covers either requirement.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.