Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green PCB power adapter board with 24-pin ATX connector, CPU 4+4 pin, SATA, graphics card 2+6 pin and DC5525 sockets

myVolts

myVolts LD-A450WL 450W AT power supply

SKU CH-KRV0-SMW3H MPN LD-A450WL

An AT power supply adapter board delivering 450 W from a 12 V input, plugging directly into a 24-pin ATX connector to remove 24 wires and save case space.

  • TypeAT
  • Saves chassis space by plugging directly into the ATX connector, removing 24 wires
  • Delivers 450 W from a 12 V input with +12 V rail rated at 30 A
  • Built-in short-circuit protection shuts down output instantly when a short is detected
  • Over-current protection trips at peak current to safeguard connected components
  • High heat-resistant PCB construction maintains stable operation under sustained load

Power Adapter for Small ATX Boards

The myVolts LD-A450WL is a 450W AT power adapter board that plugs directly into a motherboard ATX connector. It delivers +3.3V, +5V, +12V and +5VSB rails with a total output of 450W from a 12V input. The unit includes short-circuit and over-current protection on all major rails.

Builders Needing Cable Reduction

This adapter suits compact systems where eliminating 24 loose wires saves space and improves airflow. It provides one CPU 4+4 pin, two SATA, one 2+6 pin graphics connector and two DC5525 outputs. Builders who need more SATA ports, additional PCIe cables or a standard ATX form factor should look elsewhere.

Direct ATX24Pin Motherboard Connection

The board mounts straight onto the 24-pin ATX header, removing the traditional cable harness entirely. DC cables measure 320mm, CPU and graphics cables 340mm, and SATA cables 390mm plus 190mm daisy-chain. This fixed geometry decides whether the adapter fits your chassis layout.

Kohokohdat

  • Saves chassis space by plugging directly into the ATX connector, removing 24 wires
  • Delivers 450 W from a 12 V input with +12 V rail rated at 30 A
  • Built-in short-circuit protection shuts down output instantly when a short is detected
  • Over-current protection trips at peak current to safeguard connected components
  • High heat-resistant PCB construction maintains stable operation under sustained load

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

How much power can the 12 V rail deliver continuously before the over-current protection trips?

The 12 V rail is rated for 30 A maximum load, and the built-in over-current protection will shut the output off if the peak current is exceeded.

Does the adapter board itself add noticeable heat or noise when running all day inside a closed case?

The board has no fan and relies on its high heat-resistance PCB material; it produces no audible noise and the supplier notes high heat resistance for reliable all-day operation.

What external power source must I already have to run this ATX adapter?

You need a 12 V DC supply connected to the DC5525 input jack; the board then distributes +3.3 V, +5 V, +5 VSB and +12 V to the ATX 24-pin, CPU 4+4-pin, SATA and graphics 2+6-pin connectors.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.