Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Ultra-slim DIN-rail power supply in light-grey plastic case

myVolts

myVolts MDR-100-48 48V Power Supply

SKU CH-ZTA3-EQRPD

Ultra-slim DIN-rail AC-DC unit delivering 48 V for industrial PLCs and sensors

  • TypeAT
  • Ultra-thin DIN rail design fits TS-35/7.5 or 15 mounting
  • Universal AC input powers industrial PLC sensors and robots
  • ZCS/ZVS technology reduces power dissipation during operation
  • Free air convection cooling eliminates fan noise and failure points
  • DC OK relay contact plus LED indicator confirm power status

Industrial DIN-rail power supply

The myVolts MDR-100-48 delivers 48 V DC at up to 2 A for PLCs, sensors and automation cabinets. It mounts on TS-35/7.5 or 15 DIN rails and accepts universal AC input. A built-in DC OK relay contact signals output status while an LED shows power-on state. No-load consumption stays below 1 W.

Sustained-load behaviour

ZCS/ZVS switching reduces dissipation during continuous operation and the unit is cooled by free-air convection alone. Short-circuit, overload, over-voltage and over-temperature protections engage automatically without interrupting adjacent circuits. One hundred percent burn-in testing at full load verifies stability before shipment.

Replaces bulkier linear or early switch-mode units

The 100 W ultra-thin profile fits tight cabinet rows where older supplies cannot. The jump is worthwhile when DIN-rail mounting, universal input and a DC OK relay are required together. It is not suited for applications needing redundant hot-swap modules or output voltages other than the fixed 48 V rail.

Kohokohdat

  • Ultra-thin DIN rail design fits TS-35/7.5 or 15 mounting
  • Universal AC input powers industrial PLC sensors and robots
  • ZCS/ZVS technology reduces power dissipation during operation
  • Free air convection cooling eliminates fan noise and failure points
  • DC OK relay contact plus LED indicator confirm power status

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

How much heat and power does the MDR-100-48 produce when running continuously?

It uses free-air convection cooling with no fan, so it runs silently. No-load consumption is under 1 W, and ZCS/ZVS technology reduces dissipation under load.

What mounting hardware and wiring must I already have to install this unit?

You need a TS-35 DIN rail (7.5 mm or 15 mm) and wiring for universal AC input plus the DC output and the DC OK relay contact.

Will the 48 V output work with older 24 V or 12 V PLC sensors I want to keep?

No — this model delivers 48 V only. The MDR-100 series includes separate 12 V and 24 V versions, but each unit has a single fixed output voltage.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.