Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Rectangular aluminium power supply with screw terminals and voltage adjuster

myVolts

myVolts S-120-12 12V 10A 120W Power Supply

SKU CH-X4VB-9TCH0

A 12 V 10 A 120 W switch-mode supply with short-circuit, overload and over-voltage protection, aluminium-alloy case and CCC, FCC and CE compliance for industrial automation, LED displays, CCTV.

  • TypeAT
  • Delivers 120 W continuous power for demanding 12 V loads
  • Wide AC 100–240 V input suits global mains supplies
  • Built-in short-circuit, overload and over-voltage protection safeguards connected gear
  • Aluminium-alloy chassis runs 0–40 °C with natural convection cooling
  • Certified to CCC, FCC and CE safety standards

12 V 10 A industrial power supply

This myVolts unit delivers a regulated 12 V DC output at up to 10 A for 120 W continuous power. It accepts a universal AC input range of 100 to 240 V, making it suitable for bench use, LED installations, CCTV systems, 3D printers and similar industrial automation tasks.

120 W capacity with protection limits

The supply handles loads up to its 120 W rating with built-in overload, overvoltage and short-circuit protection that shut down the output before damage occurs. It operates reliably between 0 and 40 °C ambient; above that temperature headroom drops and sustained full-load operation is not guaranteed.

AT form-factor switch-mode design

The aluminium-alloy chassis uses natural convection cooling with no fan, so silent operation is assured in noise-sensitive environments. Terminal blocks provide L and N for AC input, GND and V for DC output, plus an ADJ trimmer for fine voltage adjustment. Safety approvals include CCC, FCC and CE.

Kohokohdat

  • Delivers 120 W continuous power for demanding 12 V loads
  • Wide AC 100–240 V input suits global mains supplies
  • Built-in short-circuit, overload and over-voltage protection safeguards connected gear
  • Aluminium-alloy chassis runs 0–40 °C with natural convection cooling
  • Certified to CCC, FCC and CE safety standards

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

Will the myVolts S-120-12 12V 10A 120W Power Supply run safely with older LED strips that only draw a few amps?

The unit delivers up to 10 A at 12 V and includes short-circuit, overload and overvoltage protection, so it will safely supply only the current your legacy strips actually draw.

How can I confirm the myVolts S-120-12 12V 10A 120W Power Supply is operating correctly once wired?

Measure the DC output at the V and GND terminals; it should read 12 V with low ripple, and the built-in ADJ trimmer lets you fine-tune the voltage if needed.

What comes in the box with the myVolts S-120-12 12V 10A 120W Power Supply and what must I source separately?

The supply itself is included; you must provide an AC mains cord for the L and N inputs and your own DC wiring for the V and GND outputs.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.