Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green printed circuit board with black memory chips, no heat spreader, 288-pin DDR4 UDIMM form factor

NEMIX RAM

NEMIX RAM 16GB DDR4 3200 2Rx8 CL22 UDIMM memory upgrade

SKU CH-WRGC-2JM1W

16 GB DDR4 3200 UDIMM module, CL22 1.20 V, 2Rx8 unbuffered, validated for Supermicro systems

  • Capacity16GB
  • SpeedDDR4 3200 (PC4 25600)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.20V
  • 16 GB DDR4 3200 memory boosts desktop responsiveness
  • 2Rx8 dual-rank organisation improves bandwidth for multitasking
  • CL22 latency at 1.20 V balances speed and efficiency
  • 288-pin UDIMM form factor fits standard desktop slots
  • Built with major OEM chips for reliable compatibility

16GB DDR4 3200 UDIMM for Supermicro

This NEMIX RAM module provides 16GB of DDR4 3200 memory in a single 288-pin UDIMM. It operates at 1.2V with CL22 latency and uses a 2Rx8 rank configuration built with major OEM chips. The non-ECC unbuffered design targets compatible Supermicro desktop and workstation platforms.

Suits Supermicro upgrades needing non-ECC UDIMMs

Builders expanding a supported Supermicro system with standard unbuffered memory will find this module matches the required specifications. It is not for servers that require registered or ECC modules, nor for platforms limited to lower densities or different DDR generations.

Verify motherboard accepts 16GB 2Rx8 non-ECC UDIMMs

Check your Supermicro motherboard manual for maximum capacity per slot and supported rank configurations. Confirm the board runs DDR4 at 3200 MT/s and does not require registered or ECC memory. Ensure an empty 288-pin DIMM slot is available for installation.

Kohokohdat

  • 16 GB DDR4 3200 memory boosts desktop responsiveness
  • 2Rx8 dual-rank organisation improves bandwidth for multitasking
  • CL22 latency at 1.20 V balances speed and efficiency
  • 288-pin UDIMM form factor fits standard desktop slots
  • Built with major OEM chips for reliable compatibility

Tekniset tiedot

BrandNEMIX RAM
SeriesSuperMicro Server/Workstation Compatible Series Memory
ModelSuperMicro DDR4 3200MHZ Non-ECC Unbuffered UDIMM
Part NumberMD25600-628K1
Capacity16GB
SpeedDDR4 3200 (PC4 25600)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.20V
Compatible SystemSupermicro
CAS LatencyCL22
Heat SpreaderNo
Type288-Pin DDR4 UDIMM
Rank2Rx8
FeaturesDDR4 Non- ECC Unbuffered UDIMM Motherboard Compatible
Package Content16GB (1X16GB) DDR4 3200MHZ PC4-25600 2Rx8 1.2V CL22 288-PIN Non-ECC Unbuffered UDIMM

Kysymyksiä tästä tuotteesta

Does my motherboard need a free 288-pin DDR4 slot to install this UDIMM?

Yes, the module uses the standard 288-pin DDR4 UDIMM form factor and requires an available DDR4 DIMM slot on a compatible motherboard.

Can I add this CL22 3200MHz stick alongside slower DDR4 modules already in my system?

The memory will run at the lowest common speed and loosest timings across all installed modules, so it will downclock to match slower DDR4 sticks.

How can I confirm the module is detected at 3200MHz with CL22 after installation?

Check the BIOS memory information screen or use a system utility such as CPU-Z to verify the reported speed of 3200MHz and CAS latency of CL22.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.