Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with black memory chips, no heat spreader, gold edge connector

NEMIX RAM

NEMIX RAM 16GB DDR5 5600 CL46 1Rx8 1.1V UDIMM Supermicro BH4SRG memory upgrade

SKU CH-YNPC-JN7F9

16GB DDR5 5600 CL46 unbuffered UDIMM for Supermicro BH4SRG motherboards

  • Capacity16GB
  • SpeedDDR5 5600 (PC5 44800)
  • ECCNo
  • Buffered/RegisteredUnbuffered
  • ChipsetMajor OEM Samsung, Micron, Hynix
  • Voltage1.10V
  • 16 GB DDR5 5600 MHz boosts system responsiveness
  • CL46 latency keeps data flowing smoothly at rated speed
  • 1 V operation reduces power draw and heat
  • Single-rank 1Rx8 layout simplifies memory controller loading
  • 288-pin UDIMM fits Supermicro BH4SRG motherboards directly

Supermicro BH4SRG DDR5 upgrade

This 16 GB DDR5 module is built for the Supermicro BH4SRG motherboard. It targets owners who want a single-slot capacity increase without mixing speeds or ranks. The part carries a CL46 timing at 5600 MT/s and runs at the standard 1.1 V.

Unbuffered UDIMM with major-brand chips

The stick uses 1Rx8 organisation and a 288-pin UDIMM form factor with no heat spreader. Samsung, Micron or Hynix ICs are selected by the assembler, and the unbuffered design means it drops straight into standard desktop DIMM slots. Installation follows the usual latch-and-seat routine.

JEDEC baseline limits overclock headroom

Operating at the base DDR5 5600 specification, the module does not offer XMP or EXPO profiles for higher frequencies. Builders who need lower latency or faster data rates will have to look beyond this JEDEC-standard part. Non-ECC operation also rules out error-correction workloads.

Kohokohdat

  • 16 GB DDR5 5600 MHz boosts system responsiveness
  • CL46 latency keeps data flowing smoothly at rated speed
  • 1 V operation reduces power draw and heat
  • Single-rank 1Rx8 layout simplifies memory controller loading
  • 288-pin UDIMM fits Supermicro BH4SRG motherboards directly

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-618K1
Capacity16GB
SpeedDDR5 5600 (PC5 44800)
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor OEM Samsung, Micron, Hynix
Voltage1.10V
Compatible SystemSupermicro
CAS LatencyCL46
Heat SpreaderNo
Type288-Pin DDR5 UDIMM
Rank1Rx8
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content16GB (1 x 16GB) DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM

Kysymyksiä tästä tuotteesta

Does this DDR5 5600 module run at its rated speed on the Supermicro BH4SRG motherboard?

The module is specified as DDR5 5600 (PC5-44800) and listed as compatible with the Supermicro BH4SRG motherboard.

Will this 288-pin UDIMM fit the DIMM slots on the Supermicro BH4SRG board?

It is a 288-pin DDR5 UDIMM, the standard form factor for desktop DDR5 motherboards including the BH4SRG.

What is the correct way to seat this single-rank 1Rx8 module, and what step do builders often miss?

Align the notch with the slot key, press down firmly until both retention clips click, then verify the module is fully seated by checking that no gold contacts are visible.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.