BFKK
BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
214,99 $
0.00277962BTC
Varastossa
NEMIX RAM
NEMIX RAM 8GB (2x4GB) DDR3 1333 PC3-10600 1.35V 204-Pin SODIMM Kit for POSIFLEX XT-5415IR
DDR3 SODIMM kit adds 8 GB across two 4 GB modules running at 1333 MHz for the POSIFLEX XT-5415IR terminal
- Capacity8GB (2 x 4GB)
- SpeedDDR3 1333 (PC3 10600)
- ECCNo
- Buffered/RegisteredUnbuffered
- ChipsetMajor OEM Samsung, Micron, Hynix
- Voltage1.50V
- Designed for POSIFLEX XT-5415IR JIVA POS terminals
- Dual-channel 8 GB kit boosts multitasking in point-of-sale systems
- Low-voltage 1.35 V DDR3 reduces power draw in fanless units
- CL9 latency at 1333 MHz ensures responsive transaction processing
- Built with major-brand Samsung, Micron or Hynix chips for reliability
System-specific DDR3 kit for POSIFLEX XT-5415IR
This 8 GB kit contains two 4 GB DDR3 1333 SODIMM modules built for the POSIFLEX XT-5415IR JIVA terminal. Each stick is a 204-pin 2Rx8 unbuffered non-ECC part rated at PC3-10600 with CL9 latency. The kit targets service technicians and IT teams maintaining or upgrading this exact point-of-sale platform.
Factory-matched pair eliminates slot mismatch
The two modules are packaged together as a tested pair, so both slots receive identical 1.35 V 1333 MHz sticks from the same OEM chip supply (Samsung, Micron or Hynix). This removes the risk of mixing ranks, voltages or vendors that can cause POST failures on the fanless terminal. No extra software, drivers or heat spreaders are included or required.
Tool-free slot access; verify BIOS recognition
The XT-5415IR chassis opens without tools, exposing the SODIMM slots for a straightforward swap. Insert each module at the correct angle until the retention clips engage. If the terminal does not show the full 8 GB at boot, reseat both sticks and confirm the BIOS revision supports the 2Rx8 density; some earlier revisions may not initialise the second rank.
Kohokohdat
- Designed for POSIFLEX XT-5415IR JIVA POS terminals
- Dual-channel 8 GB kit boosts multitasking in point-of-sale systems
- Low-voltage 1.35 V DDR3 reduces power draw in fanless units
- CL9 latency at 1333 MHz ensures responsive transaction processing
- Built with major-brand Samsung, Micron or Hynix chips for reliability
Tekniset tiedot
| Brand | NEMIX RAM |
|---|---|
| Series | POSIFLEX POS Series Point of Sale Kiosk Memory |
| Model | POSIFLEX POS DDR3 1333MHZ Non-ECC Unbuffered SODIMM |
| Part Number | MS10600-428K2 |
| Capacity | 8GB (2 x 4GB) |
| Speed | DDR3 1333 (PC3 10600) |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major OEM Samsung, Micron, Hynix |
| Voltage | 1.50V |
| Compatible System | POSIFLEX POS |
| CAS Latency | CL9 |
| Heat Spreader | No |
| Type | 204-Pin DDR3 SODIMM |
| Rank | 2Rx8 |
| Features | DDR3 Non-ECC Unbuffered SODIMM Motherboard Compatible |
| Package Content | 8GB (2X4GB) DDR3 1333MHZ PC3-10600 2Rx8 1.35V 204-PIN Non-ECC Unbuffered SODIMM KIT |
Kysymyksiä tästä tuotteesta
Will the 2Rx8 DDR3 SODIMMs need any firmware updates or periodic reseating after installation?
No firmware updates or scheduled reseating are required for the 2Rx8 DDR3 SODIMMs; they are non-ECC unbuffered modules designed for continuous operation in the POSIFLEX XT-5415IR terminal.
What is the first limit reached when the memory runs at 1333 MHz CL9 under sustained load?
The first limit is the fixed DDR3 1333 speed and CL9 latency; bandwidth and timing cannot exceed the PC3-10600 specification during prolonged use.
How much heat and power do the 1.35 V modules produce when the fanless POS terminal runs all day?
The modules operate at 1.35 V without a heat spreader, drawing minimal power and generating low heat suitable for the fanless POSIFLEX XT-5415IR enclosure.
Myös tällä osastolla
Asiakkaat vertailivat myös näitä
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
BFKK
BFKK 2U Micro ATX Rackmount 2×5.25" 4×3.5" Side 80mm Fan
- Rackmount
216,99 $
0.00280548BTC
Varastossa
