Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green DDR5 UDIMM modules, no heat spreaders, 288 pins each

NEMIX RAM

NEMIX RAM DDR5 5600 CL46 32GB (2x16GB) 1Rx8 1.1V UDIMM Supermicro X13SAE memory upgrade

SKU CH-48PC-VNXFZ

A 32 GB DDR5-5600 kit (2 × 16 GB, CL46, 1.1 V, 1Rx8, 288-pin UDIMM) validated for the Supermicro X13SAE motherboard

  • Capacity32GB (2 x 16GB)
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 32GB 2X16GB

  • 32 GB kit expands desktop capacity with two 16 GB modules
  • DDR5 5600 speed matches the board's rated memory frequency
  • CL46 latency and 1.1 V voltage meet the controller's exact timing requirements
  • 1Rx8 unbuffered UDIMM form factor fits the Supermicro X13SAE motherboard slots
  • Major OEM chips from Samsung, Micron or Hynix tested for stability at rated specifications

Targeted DDR5 upgrade for Supermicro X13SAE

This 32 GB kit delivers two 16 GB DDR5-5600 UDIMMs built to the exact rank, voltage and timing the X13SAE memory controller expects. The 1Rx8 organisation, 1.1 V operation and CL46 latency match the board specification so the system recognises the full capacity at rated speed. No heat spreader is fitted, keeping the modules compatible with standard CPU coolers.

Suits builders adding capacity to a Supermicro

The kit is designed for non-ECC unbuffered DDR5 slots only; it will not function in servers that require registered or ECC memory. Buyers needing error-correcting code, registered DIMMs or SODIMM form factors should look elsewhere. The 288-pin UDIMM layout also prevents installation in any platform using a different pin count or DDR generation.

The CL46 latency at 1.1 V decides compatibility

The X13SAE firmware is validated for DDR5-5600 at CL46 with 1.1 V 1Rx8 UDIMMs. Modules with different timings, voltages or rank structures may not train at the rated frequency or may not be recognised at all. Confirm the motherboard manual supports this exact CAS latency and voltage combination before purchase.

Kohokohdat

  • 32 GB kit expands desktop capacity with two 16 GB modules
  • DDR5 5600 speed matches the board's rated memory frequency
  • CL46 latency and 1.1 V voltage meet the controller's exact timing requirements
  • 1Rx8 unbuffered UDIMM form factor fits the Supermicro X13SAE motherboard slots
  • Major OEM chips from Samsung, Micron or Hynix tested for stability at rated specifications

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-618K2
Capacity32GB (2 x 16GB)
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content32GB 2X16GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Does my Supermicro X13SAE motherboard need a specific DDR5 slot layout for this 288-pin UDIMM kit?

The kit uses the 288-pin DDR5 UDIMM form factor required by the X13SAE. Check your manual for the approved DIMM population order before installing the two 16 GB modules.

Can I keep my existing DDR5 memory and add this CL46 1.1 V kit alongside it?

Mixing kits with different CAS latency, voltage, or rank (this kit is 1Rx8 CL46 at 1.1 V) can prevent the board from running at 5600 MHz. For stable operation use identical modules in all populated slots.

How do I confirm the system is running at the rated DDR5 5600 speed after installing the kit?

Enter the BIOS or use a system-information tool and verify the memory frequency shows 5600 MT/s (PC5-44800) with CL46 timings at 1.1 V.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.