Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Ten black 40mm square cooling fans with 2-pin connectors

OEM Industries

OEM Industries FSY40S24M 40mm Fan 10 Pcs 24V 2 Pin

SKU CH-JSE7-YSM84

Pack of ten 40 mm sleeve-bearing fans running at 24 V with two-pin connectors

  • ColorBlack
  • TypeFan only
  • Fan Size40mm
  • Bearing TypeSleeve Bearing
  • Power Connector2 Pin
  • LEDNo
  • Ten fans in one pack simplify multi-unit builds
  • 40 mm square frame fits tight 4010 mounting holes
  • 24 V 0.1 A rating keeps power draw low
  • Two-pin connector enables direct board connection
  • Sleeve bearing design reduces mechanical complexity

40 mm Sleeve-Bearing Fans for 24 V Systems

This pack contains ten 40 mm square fans designed for 24 V power rails. Each unit draws 0.1 A through a two-pin connector and uses a sleeve bearing. The fans suit builders who need multiple low-profile coolers for tight enclosures or replacement parts for legacy hardware.

Thermals Noise and Power Draw

At 24 V the fans run on a modest 0.1 A current, keeping power draw low in normal operation. Sleeve bearings typically produce a gentle airflow sound that stays quiet at modest speeds. The simple two-wire design means speed is fixed unless an external controller is added.

Upgrade Path and Compatibility

These fans replace worn 40 mm sleeve-bearing units in industrial gear, small form-factor PCs or embedded boards that already use a 24 V two-pin header. They are not suited for builders who need PWM speed control, larger frame sizes or higher static pressure for dense heatsinks.

Kohokohdat

  • Ten fans in one pack simplify multi-unit builds
  • 40 mm square frame fits tight 4010 mounting holes
  • 24 V 0.1 A rating keeps power draw low
  • Two-pin connector enables direct board connection
  • Sleeve bearing design reduces mechanical complexity

Tekniset tiedot

ModelFSY40S24M
ColorBlack
TypeFan only
Fan Size40mm
Bearing TypeSleeve Bearing
Power Connector2 Pin
LEDNo

Kysymyksiä tästä tuotteesta

How do I install the 40mm fan using the 2-pin connector?

Align the 2-pin connector with the 24V header on your board, press it straight on, and route the wires so the 40*10mm frame sits flat; the step most people miss is checking polarity before powering up.

What maintenance will the sleeve bearing need over time?

The sleeve bearing runs dry eventually; when noise rises or speed falls, swap in another unit from the 10-piece pack.

What limit appears first when the fan runs continuously at 24V 0.1A?

Continuous operation at the rated 24V 0.1A will wear the sleeve bearing lubricant first, leading to audible rumble and reduced rpm.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.