Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black 92mm sleeve bearing cooling fan with two wires

OEM Industries

OEM Industries JF0925S1M 92mm Sleeve Bearing Fan

SKU CH-HBPM-PYRDK

A 92mm sleeve-bearing DC fan with a 2-wire 12V 0.20A connection for targeted component cooling

  • ColorBlack
  • TypeFan only
  • Fan Size92mm
  • Bearing TypeSleeve Bearing
  • Power Connector2 Wires
  • LEDNo
  • 92 mm frame fits compact CPU cooler builds
  • Sleeve bearing keeps acoustic profile low for quiet operation
  • 12 V 0.20 A draw limits power budget impact
  • Two-wire connector simplifies installation on standard headers
  • Black finish blends cleanly with dark-themed builds

92 mm Sleeve Bearing Replacement Fan

This 92 mm sleeve bearing fan suits builders who need a direct replacement for a JF0925S1M cooler. It runs on a 12 V two-wire connection and draws 0.20 A. The black frame matches most standard CPU air coolers. It is not for buyers who need PWM speed control or a three-pin header.

Thermals Noise and Power Draw

The sleeve bearing keeps acoustic output low during typical desktop workloads. At 0.20 A the fan draws minimal power from the 12 V rail. No LED lighting means no extra current draw or visual distraction inside the case. The two-wire design reports no speed signal to the motherboard.

Sustained Load Behaviour

Under continuous load the sleeve bearing maintains consistent rotation without the rattle that can develop in some ball-bearing units. The fixed-voltage design keeps airflow steady rather than ramping with temperature. Builders who want automatic fan curves should choose a PWM model instead.

Kohokohdat

  • 92 mm frame fits compact CPU cooler builds
  • Sleeve bearing keeps acoustic profile low for quiet operation
  • 12 V 0.20 A draw limits power budget impact
  • Two-wire connector simplifies installation on standard headers
  • Black finish blends cleanly with dark-themed builds

Tekniset tiedot

ModelJF0925S1M
ColorBlack
TypeFan only
Fan Size92mm
Bearing TypeSleeve Bearing
Power Connector2 Wires
LEDNo

Kysymyksiä tästä tuotteesta

How do I mount the 92 mm JF0925S1M fan, and which step often goes wrong?

Line up the four corner holes with your chassis or heatsink, insert the screws diagonally and tighten evenly; the common mistake is over-tightening one corner first, which warps the frame and adds vibration.

What maintenance will the sleeve bearing need later?

Sleeve bearings run on a thin oil film that gradually dries; when the fan becomes noisy or rpm drops, the only fix is to replace the whole unit.

What limit appears first during continuous 12 V operation?

The 0.20 A sleeve-bearing motor hits its thermal and wear ceiling before the wiring or connector does, so sustained load eventually degrades spin speed and acoustics.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.