Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Small black VGA cooling fan with two wires and a 2-pin connector

OEM Industries

OEM Industries MGA5012MR-O10 12V 0.1A 2-pin VGA cooling fan

SKU CH-VQ3P-N4WRR

A 12 V, 0.1 A two-pin fan cools graphics cards with 5012 model airflow

  • ColorBlack
  • TypeAccessories
  • Power Connector2 Pin
  • 2-pin connector enables direct VGA card power
  • 12 V 0.1 A rating keeps graphics card cool
  • Compact accessory fits tight video card spaces
  • Black finish matches typical GPU shroud aesthetics
  • New condition ensures reliable long-term operation

Replacement GPU cooler fan

The OEM Industries MGA5012MR-O10 is a 12 V 0.1 A two-pin fan built for graphics-card cooling. It suits owners of a compatible video card who need a direct replacement for a worn or noisy original unit. The black accessory installs using the existing two-wire header on the board. Buyers who need a different voltage, connector type or higher airflow should look elsewhere.

Low power draw and simple wiring

Rated at 12 V and 0.1 A, the fan draws minimal current from the graphics card's onboard header. The two-pin connection supplies power without PWM control, so speed stays constant whenever the card is running. This arrangement keeps wiring straightforward and avoids extra load on the GPU's fan controller. No figures for noise level or static pressure are supplied.

Compact two-wire drop-in fit

The black plastic frame mounts directly onto the card's existing screw holes using the supplied two wires and two-pin plug. No adapters or soldering are required when the original cooler matches the MGA5012MR-O10 footprint. Installers should verify physical dimensions against the old fan before fitting. Cards with three-pin, four-pin or proprietary headers cannot use this cooler.

Kohokohdat

  • 2-pin connector enables direct VGA card power
  • 12 V 0.1 A rating keeps graphics card cool
  • Compact accessory fits tight video card spaces
  • Black finish matches typical GPU shroud aesthetics
  • New condition ensures reliable long-term operation

Tekniset tiedot

ModelMGA5012MR-O10
ColorBlack
TypeAccessories
Power Connector2 Pin

Kysymyksiä tästä tuotteesta

How do I install the 2-pin power connector on the MGA5012MR-O10 and what step do people often miss?

Align the two wires with the header on the graphics card and press straight down until the latch clicks; the step most people miss is verifying the black wire sits on the ground pin before powering on.

What maintenance will the 12V 0.1A fan need over time?

Dust builds up on the blades and reduces airflow, so use compressed air every few months to clear it; the sleeve bearing cannot be lubricated, so plan to replace the unit when noise increases.

What limit appears first when the MGA5012MR-O10 runs continuously at full load?

The 0.1 A current rating caps the maximum airflow, so sustained loads hit the thermal ceiling of the fan itself before the 12 V supply becomes a constraint.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.