Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two small two-tone cooling fans with four-pin connectors

OEM Industries

OEM Industries PLA08015B12HH PLB07010D12M 4-Pin CPU Cooler Fan 2-Pack

SKU CH-6NFT-QM3G0

Two 4-pin ball-bearing fans for GTS450 and GTS 250 graphics card cooling

  • Color2-Tone
  • TypeFan only
  • Bearing TypeBall
  • Power Connector4 Pin
  • LEDNo
  • Two fans included for dual-slot GPU cooling
  • 4-pin PWM connectors enable precise speed control
  • Ball-bearing design extends operational lifespan
  • 12 V operation draws 0.35 A and 0.30 A respectively
  • Compatible with GTS 450, GTS 250 and GT 250 cards

Two-Fan Kit for Legacy GPU Coolers

This set includes two 4-pin cooling fans built for specific Power Logic models PLA08015B12HH and PLB07010D12M. They are intended as direct replacements on older graphics cards such as the GTS 450, GTS 250 or GT 250 where the original circular fans have failed. Ball bearings and a two-tone finish complete the package.

Check Connector Clearance and Voltage

Verify that your card uses a 4-wire PWM header and that the mounting holes match the circular layout shown for the reference models. The fans run at 12 V with current draws of 0.35 A and 0.30 A respectively, so the board header must supply enough current for both units. No LED lighting is present if your build relies on visual sync.

Ball Bearings Deliver Steady Airflow

Dual ball-bearing construction keeps operating noise consistent over long sessions without the rattle that sleeve bearings develop. Each fan draws modest power at 12 V, so total system load remains low even when both units spin at full speed. Expect reliable thermal performance for the supported legacy GPUs under typical gaming or compute loads.

Kohokohdat

  • Two fans included for dual-slot GPU cooling
  • 4-pin PWM connectors enable precise speed control
  • Ball-bearing design extends operational lifespan
  • 12 V operation draws 0.35 A and 0.30 A respectively
  • Compatible with GTS 450, GTS 250 and GT 250 cards

Tekniset tiedot

ModelPLA08015B12HH PLB07010D12M
Color2-Tone
TypeFan only
Bearing TypeBall
Power Connector4 Pin
LEDNo

Kysymyksiä tästä tuotteesta

What comes in the box and is any extra cable or bracket needed?

The pack contains two 4-pin fans only. No additional cables, brackets or mounting hardware are included.

Which of the two model numbers should I pick for my card?

PLA08015B12HH draws 0.35 A and PLB07010D12M draws 0.30 A at 12 V; choose the one that matches the original fan label on your graphics card.

What do the 0.35 A and 0.30 A ratings mean once the fans are installed?

They show the maximum 12 V current each fan can draw from the motherboard or GPU header.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.