Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black 60mm PWM fan with four-pin connector and ball bearing

OEM Industries

OEM Industries SHBC0612HB 60mm 12V 0.18A 4-pin PWM CPU cooler

SKU CH-BB8P-FAWQY

A 60 mm PWM fan with dual ball bearings and a 4-pin connector for CPU or case cooling

  • ColorBlack
  • TypeFan only
  • Fan Size60mm
  • Bearing TypeBall
  • Power Connector4 Pin
  • LEDNo
  • 60 mm fan fits compact CPU coolers and tight case layouts
  • 12 V 0.18 A draw keeps power load low for small-form-factor builds
  • Dual ball bearing reduces wear and extends operating life
  • 4-pin PWM connector enables automatic speed control from the motherboard
  • Fan-only design lets you pair it with any compatible heatsink

Compact 60 mm PWM fan

The OEM Industries SHBC0612HB is a 60 mm square fan with a 4-pin PWM connector that runs on 12 V and draws 0.18 A. It uses a dual ball-bearing design for consistent rotation and has no integrated lighting. The unit is sold as a fan only, without a heatsink or mounting hardware.

Suited for tight clearance builds

This fan fits small-form-factor cases and low-profile coolers where a 60 mm frame is the maximum allowed size. The PWM wire lets the motherboard control speed automatically, so noise stays low at idle. Builders who need higher static pressure for dense radiators or larger heatsinks should look at bigger frame sizes instead.

Airflow headroom for light loads

At 12 V the motor draws 0.18 A, which is typical for a low-power 60 mm fan and provides enough airflow for modest thermal loads such as office CPUs or auxiliary case ventilation. Under sustained heavy loads the smaller blade area and limited pressure will reach their limit quickly, so the fan is not intended for high-TDP processors or overclocked configurations.

Kohokohdat

  • 60 mm fan fits compact CPU coolers and tight case layouts
  • 12 V 0.18 A draw keeps power load low for small-form-factor builds
  • Dual ball bearing reduces wear and extends operating life
  • 4-pin PWM connector enables automatic speed control from the motherboard
  • Fan-only design lets you pair it with any compatible heatsink

Tekniset tiedot

ModelSHBC0612HB
ColorBlack
TypeFan only
Fan Size60mm
Bearing TypeBall
Power Connector4 Pin
LEDNo

Kysymyksiä tästä tuotteesta

Does my motherboard need a 4-pin PWM header to run the SHBC0612HB fan?

Yes, the SHBC0612HB uses a 4-pin PWM connector, so your motherboard or fan controller must provide a matching 4-pin header for speed control and monitoring.

Can I replace the stock 60 mm fan on an older heatsink with this 12 V 0.18 A ball-bearing model?

The SHBC0612HB is a 60 mm frame with 4-wire PWM and dual ball bearings, so it will fit any cooler or case mount designed for a standard 6015 fan footprint.

How can I verify the SHBC0612HB is reporting speed correctly after installation?

Enter the BIOS or open a hardware-monitoring utility and confirm the fan RPM readout changes smoothly as the PWM duty cycle ramps up and down.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.