Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two green DDR3 ECC RDIMM sticks, no heat spreader

OWC

OWC 16GB (2x8GB) DDR3 1600 ECC Registered RDIMM HP Z820

SKU CH-DRA2-3SZRT

16 GB dual-channel DDR3-1600 ECC registered RDIMM kit for HP Z820 workstations

  • Capacity16GB (2 x 8GB)
  • Type240-Pin DDR3 ECC RDIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCYes

Capacity 16GB (2 x 8GB)

  • ECC registered design prevents data corruption in critical workloads
  • 16 GB dual-channel kit (2 × 8 GB) expands Z820 capacity
  • DDR3 1600 CL11 matches factory speed for stable operation
  • 5 V JEDEC voltage ensures broad workstation compatibility
  • Replaces nine HP part numbers for straightforward upgrades

Targeted Workstation Upgrade

This OWC kit supplies 16GB of DDR3 ECC Registered memory in two 8GB modules rated at 1600MHz with CL11 latency. It is built specifically for the HP Workstation Z820 and replaces a range of original HP part numbers. The modules run at 1.5V and use a 240-pin RDIMM form factor with 1Rx4 organisation.

Not for Standard Desktops

This memory suits administrators extending the life of a Z820 workstation or server infrastructure that requires registered ECC DIMMs. It will not work in standard desktop computers that accept only unbuffered non-ECC modules, and it cannot be mixed with unbuffered memory in the same system.

Straightforward Module Installation

Installation follows the usual DIMM slot procedure for the Z820: power down, open the chassis, align the notch on each 240-pin module, and press firmly until the retention clips engage. The most common issue is attempting to install these registered DIMMs in a platform that expects unbuffered memory, which prevents the system from posting.

Kohokohdat

  • ECC registered design prevents data corruption in critical workloads
  • 16 GB dual-channel kit (2 × 8 GB) expands Z820 capacity
  • DDR3 1600 CL11 matches factory speed for stable operation
  • 5 V JEDEC voltage ensures broad workstation compatibility
  • Replaces nine HP part numbers for straightforward upgrades

Tekniset tiedot

BrandOWC
Part Number1R6D31R4016P
Capacity16GB (2 x 8GB)
Type240-Pin DDR3 ECC RDIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCYes
Buffered/RegisteredRegistered
Rank1Rx4
Heat SpreaderNo
Compatible SystemHP Workstation Z820

Tämän mallin muut versiot

4 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Does my HP Z820 need to support DDR3 1600 ECC Registered RDIMM modules for this kit to work?

Yes, the Z820 must accept DDR3 1600 PC3-12800 CL11 1.5 V ECC Registered 240-pin RDIMMs; this kit will not work in systems that only take unbuffered or non-ECC memory.

Can I keep my existing HP Z820 memory and add this 16 GB kit alongside it?

You can add this kit if the Z820 has free 240-pin slots and the installed modules are also DDR3 1600 ECC Registered; mixing with unbuffered DIMMs is not supported.

How do I confirm the Z820 recognises both 8 GB modules at 1600 MHz after installation?

Check the BIOS memory summary or the operating system memory report — both should show 16 GB total running at DDR3 1600 with ECC active.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.