Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with black memory chips and gold edge contacts

OWC

OWC 8GB DDR4 2133MHz CL15 1.2V 288-pin UDIMM for HP ProDesk 600 G3

SKU CH-HS3M-Y9VWN

Adds 8GB of DDR4 2133MHz memory to HP ProDesk 600 G3 SFF or Tower systems for faster multitasking

  • Capacity8GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • 8GB capacity expands multitasking headroom for daily workloads
  • DDR4 2133MHz CL15 timing delivers responsive system performance
  • 2V operation reduces power draw and heat output
  • 288-pin UDIMM form factor fits HP ProDesk 600 G3 SFF and Tower
  • JEDEC and RoHS compliant for warranty-safe upgrade confidence

System-specific DDR4 UDIMM for HP ProDesk 600 G3

This 8GB DDR4 2133MHz CL15 module is built for HP ProDesk 600 G3 SFF and Tower desktops. It uses a 288-pin unbuffered non-ECC design at 1.2V. The part suits office workers and IT teams who need a reliable, JEDEC-compliant memory upgrade for these exact models.

Upgrade from lower-capacity or slower DDR4 DIMMs

Replacing a 4GB stick or a slower DDR4 module with this 8GB CL15 kit adds headroom for multitasking and larger files. The jump is worth it when the system currently runs near memory limits during daily workloads. It will not fit systems that require ECC registered memory or a different DDR generation.

Tool-free installation with common pitfalls noted

The DIMM seats in the standard UDIMM slot; alignment notch and latch clicks confirm seating. Common issues include mixing ranks or speeds across channels, leaving a slot empty in dual-channel pairs, or forgetting to clear CMOS if the system fails to POST. No heat spreader means airflow matters in cramped SFF chassis.

Kohokohdat

  • 8GB capacity expands multitasking headroom for daily workloads
  • DDR4 2133MHz CL15 timing delivers responsive system performance
  • 2V operation reduces power draw and heat output
  • 288-pin UDIMM form factor fits HP ProDesk 600 G3 SFF and Tower
  • JEDEC and RoHS compliant for warranty-safe upgrade confidence

Tekniset tiedot

BrandOWC
Part Number2U1D42R808GB
Capacity8GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
Heat SpreaderNo
Compatible SystemHP ProDesk 600 G3 SFF
HP ProDesk 600 G3 Tower

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Does this 288-pin DDR4 UDIMM fit the HP ProDesk 600 G3 SFF and Tower chassis?

Yes, the module is a 288-pin unbuffered DDR4 DIMM validated for both the 600 G3 SFF and 600 G3 Tower form factors.

What is the correct way to seat the module and which step do DIYers often miss?

Align the notch with the slot key, press straight down until both side clips snap shut, then verify the system reports 2133 MHz CL15 in BIOS.

Will the 1.2 V CL15 kit ever need a firmware update or scheduled replacement?

No firmware updates apply to standard DDR4 UDIMMs; the modules carry a limited lifetime warranty and only require replacement if a memory test reports errors.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.