Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
UV orange G1/4 90 degree rotary elbow fitting 15mm extension 37.7mm tall

PrimoChill

PrimoChill G1/4 90° Rotary 15mm Elbow Fitting UV Orange

SKU CH-JNR8-8H63Z

A G1/4 rotary elbow fitting with a 15 mm extension and 360° swivel for angled liquid-cooling runs

  • TypeFittings
  • Rotates 360° for flexible tubing routing
  • 90° elbow redirects flow around tight spaces
  • 15mm extension clears nearby components
  • Brass body with UV orange powder coat
  • G1/4 threads fit standard water-cooling loops

Loop redirection fitting

The PrimoChill G1/4 90° rotary elbow fitting lets custom-loop builders change tubing direction by ninety degrees while rotating three hundred and sixty degrees for precise alignment. Its fifteen millimetre extension adds clearance around tight components. The UV orange powder-coated brass body suits themed builds.

Upgrade from fixed elbows

This fitting replaces rigid ninety degree adapters that cannot swivel after installation. The rotary joint is worth it when tubing runs must avoid motherboard heatsinks, GPU backplates or reservoir ports that sit at awkward angles. Fixed elbows force compromise on tube routing; this adapter removes that constraint.

Build integration

The male to female G1/4 threads connect directly to standard water-blocks, radiators or pump tops without extra adapters. Installed base height is fifteen millimetres and total height is thirty seven point seven millimetres, leaving room for adjacent fittings. Thread depth is five millimetres. The rotary seal frees the builder from pre-planning exact rotational orientation during loop assembly.

Kohokohdat

  • Rotates 360° for flexible tubing routing
  • 90° elbow redirects flow around tight spaces
  • 15mm extension clears nearby components
  • Brass body with UV orange powder coat
  • G1/4 threads fit standard water-cooling loops

Tekniset tiedot

TypeFittings

Kysymyksiä tästä tuotteesta

What clearance does the 15 mm extension add for the G1/4 90° rotary elbow?

The 15 mm installed base height provides extra clearance so tubing can clear nearby components while the 360° rotary lets you aim the outlet in any direction.

How is the G1/4 rotary elbow installed and what step is often missed?

Screw the male G1/4 thread 5 mm deep into the port, then rotate the female end to the desired angle before tightening; skipping the alignment step can stress the tubing run.

When should the UV orange SX powder-coated fitting be inspected or replaced?

Inspect the brass threads and O-ring seal during each loop maintenance; replace if the powder coat shows cracking, the threads gall, or any coolant weep appears at the 37.7 mm body.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.