Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
SMUGDESK 8-port ARGB hub with wireless remote, magnetic base, compact black box

SMUGDESK

SMUGDESK 8-Port 5V ARGB RGBW Magnetic Hub with Wireless Remote

SKU CH-8Z8E-M4S8R

Eight-port 5V ARGB/RGBW hub with magnetic mounting and wireless remote for flicker-free lighting control

  • Connect up to 8 ARGB or RGBW devices from one header
  • Magnetic base attaches securely to any metal surface inside the case
  • Wireless remote adjusts modes, colours, brightness and speed without software
  • PWM signal output delivers flicker-free, smooth lighting effects
  • Plug-and-play design requires no drivers for quick DIY installation

8-Port 5V ARGB RGBW Hub

This SMUGDESK hub expands a single motherboard 5V header to eight channels for addressable LED strips and fans. The magnetic base attaches to any steel surface inside the case without screws or tape. A wireless remote controls modes, colours, brightness and speed without software. PWM signal output keeps effects flicker-free for smooth lighting.

Upgrade from limited headers

Builders whose board offers only one or two 5V ARGB connectors can run up to eight devices from a single header. The jump is worth it when you want synchronised strips and fans across the whole chassis without daisy-chain limits. It does not support 12V RGB gear, so owners of older four-pin RGB hardware cannot use this hub.

Check header voltage and power budget

Verify your motherboard provides a 5V 3-pin ARGB header; connecting to 12V RGB will damage the lighting hardware. Add up the draw of all attached strips and fans to stay within the header’s current limit. Ensure the magnetic mounting spot is clear of sharp edges or moving cables.

Kohokohdat

  • Connect up to 8 ARGB or RGBW devices from one header
  • Magnetic base attaches securely to any metal surface inside the case
  • Wireless remote adjusts modes, colours, brightness and speed without software
  • PWM signal output delivers flicker-free, smooth lighting effects
  • Plug-and-play design requires no drivers for quick DIY installation

Tekniset tiedot

Tälle tuotteelle ei ole vielä julkaistu teknisiä tietoja.

Kysymyksiä tästä tuotteesta

Does the magnetic base attach to any metal surface inside the case?

Yes, the built-in magnetic backplate lets you stick the hub onto any ferrous panel without screws or tape, so you can reposition it freely.

How do you connect the hub to the motherboard and power it?

Plug the hub into a 5 V 3-pin ARGB header on the motherboard, then attach up to eight ARGB or RGBW devices to the hub ports; no extra drivers are required.

What should I check before adding more LED strips or fans later?

Verify that every new device is 5 V ARGB or RGBW and that the combined power draw stays within the motherboard header’s limit to avoid overload.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.