Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Small square cooling fan in two-tone finish with four-wire connector

SunnyStar Co., Ltd

SunnyStar Co., Ltd C-E01C 12V 400mA 4-Pin Fan for C260S C300S EB-C260M EB-C300MN EB-C3000X Projector

SKU CH-GTSG-WVN33

Replacement cooling fan with ball bearing, 12 V 400 mA draw and four‑pin connector for compatible projectors

  • Color2-Tone
  • TypeFan only
  • Bearing TypeBall
  • Power Connector4 Pin
  • Reliable long-life operation with ball-bearing design
  • Precise speed control via 4-pin PWM connector
  • Direct fit for C260S and C300S projectors
  • Compatible with EB-C260M and EB-C300MN models
  • Also suits EB-C3000X projector units

Projector Replacement Cooling Fan

The SunnyStar C-E01C is a new 4-pin cooling fan built to replace the original unit in compatible projectors. It runs on 12 V at 400 mA and uses a ball bearing for durable operation. The two-tone housing matches the stock appearance shown in the physical photos.

Fits Listed Projector Models Only

This fan suits owners of a C260S, C300S, EB-C260M, EB-C300MN or EB-C3000X projector who need a direct drop-in replacement. Buyers with any other projector or a different cooling assembly should look elsewhere because the connector and mounting are model-specific.

4-Pin Power Connector Decides Compatibility

The 4-pin connector is the single specification that determines whether this part will work in your machine. Verify that the original fan uses an identical 4-wire plug before ordering.

Kohokohdat

  • Reliable long-life operation with ball-bearing design
  • Precise speed control via 4-pin PWM connector
  • Direct fit for C260S and C300S projectors
  • Compatible with EB-C260M and EB-C300MN models
  • Also suits EB-C3000X projector units

Tekniset tiedot

ModelC-e01C
Color2-Tone
TypeFan only
Bearing TypeBall
Power Connector4 Pin

Kysymyksiä tästä tuotteesta

How can I verify the C-E01C fan is running correctly after installing it in my C260S projector?

Connect the 4-pin connector, power on the projector and listen for the ball-bearing motor spinning smoothly; the 12 V 400 mA rating means it should reach full speed within a few seconds without rattling.

What comes with the C-E01C and do I need any extra cables or mounting hardware for my EB-C300MN?

The package contains only the C-E01C fan unit with its attached 4-pin lead; no additional screws, brackets or adapters are included, so reuse the original mounting hardware from the projector.

Which version of the C-E01C should I choose for a C300S versus an EB-C3000X?

There is a single C-E01C model rated at 12 V 400 mA with a 4-pin connector, and it is listed as compatible with both the C300S and EB-C3000X projectors, so the same part fits either unit.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.