Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Metal 10-port PoE switch with eight RJ45 ports and two uplink ports

UGREEN 10-Port PoE Switch 8×PoE+ 60W 2×Gigabit Uplink Unmanaged

SKU CH-343H-P1VQC

A 10-port unmanaged PoE+ switch with eight 30 W ports, two gigabit uplinks and a 60 W power budget

  • StandardsPassive PoE
  • Network MediaRJ45
  • Uplink InterfaceRJ45
  • Uplink Speed10/100 Mbps
  • Uplink Speed/TypeRJ45
  • Primary Port Count10
  • 8 PoE+ ports deliver up to 30W each with 60W total budget
  • Two Gigabit uplink ports provide 1000Mbps connectivity for cameras and access points
  • One button switches between Standard, Port Isolation and Extend modes up to 820 ft
  • PoE auto recovery restarts frozen devices on ports 1-8 without manual intervention
  • Intelligent power management cuts ports in priority order 8-1 when budget exceeds 60W

10-Port PoE Switch for cameras and access points

This UGREEN switch provides eight PoE+ Gigabit ports with a 60W total power budget and two Gigabit uplink ports. It is built for installers who need to power IP cameras, wireless access points or VoIP phones from a single unmanaged device. The metal chassis supports plug-and-play deployment without software configuration.

Silent metal chassis with 60W power management

The fanless metal enclosure dissipates heat passively so the switch runs silently in office or ceiling-mount locations. When connected devices request more than 60W, the switch drops ports in priority order 81 to prevent overload. Short-circuited ports shut off independently while the remaining ports continue operating.

802.3at/af PoE+ at 30W per port decides fit

Each of the eight PoE ports delivers up to 30W under the 802.3at and 802.3af standards, but the 60W total budget means only two ports can run at full power simultaneously. Buyers who need more than 60W of combined PoE power or who require managed features such as SNMP or VLAN routing should choose a different switch.

Kohokohdat

  • 8 PoE+ ports deliver up to 30W each with 60W total budget
  • Two Gigabit uplink ports provide 1000Mbps connectivity for cameras and access points
  • One button switches between Standard, Port Isolation and Extend modes up to 820 ft
  • PoE auto recovery restarts frozen devices on ports 1-8 without manual intervention
  • Intelligent power management cuts ports in priority order 8-1 when budget exceeds 60W

Tekniset tiedot

BrandNETGEAR
SeriesProSafe
Part Number35372US
StandardsPassive PoE
Network MediaRJ45
Uplink InterfaceRJ45
Uplink Speed10/100 Mbps
Uplink Speed/TypeRJ45
Primary Port Count10
Primary Ports16 x SFP + 8 x RJ45
Primary Port Speed10/100Mbps + 1000Mbps
Primary Port TypeRJ45
Management InterfaceRJ45
Jumbo Frames9216 bytes
Packet Forwarding Rate1000 megabits_per_second
SNMPNo
Layer 2 FeaturesRJ45, 1000 megabits_per_second, 10
Layer 3 Features35372US
CablingRJ45
Certificationnot_applicable
Features10, RJ45, 1000 megabits_per_second, Metal, Grey

Kysymyksiä tästä tuotteesta

How do I install the UGREEN 10-Port PoE Switch and which step is often missed?

Connect the power adapter, link the 2 Gigabit uplink ports to your router or core switch, then plug PoE devices into the 8 PoE+ ports. The step often missed is pressing the mode button to select Standard, Port Isolation (VLAN) or Extend mode for the intended network behaviour.

What maintenance or replacement will the UGREEN 10-Port PoE Switch need over time?

The metal chassis is passively cooled with no moving parts, so no scheduled maintenance is required. If a port suffers a short circuit it shuts off independently; persistent port failures after power cycling the unit indicate the switch itself should be replaced.

What limit appears first when the UGREEN 10-Port PoE Switch runs under sustained full load?

The 60 W total PoE budget is the first constraint. When connected devices draw more than 60 W, the switch cuts power to ports in priority order starting with port 8 then port 1 to prevent overload.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.