Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Small 40mm square case fan with 7mm thickness, two-tone finish, three-pin connector

Zyvpee

Zyvpee AD0412HB-K96 40x7mm 12V 0.08A 3-pin case fan

SKU CH-SHYM-41PG7

A 40 mm ball-bearing case fan running at 1600 RPM on 12 V with a three-pin connector

  • TypeCPU Cooler Fan
  • Bearing TypeBall
  • RPM<1600 RPM
  • Power Connector3 Pin
  • Color2-Tone
  • LEDNon-LED
  • Compact 40 mm frame fits tight builds
  • Ball bearing runs below 1600 RPM for quiet operation
  • 12 V 0.08 A draw keeps power use low
  • 3-pin connector enables simple motherboard control
  • Two-tone non-LED design suits clean aesthetics

Compact 40 mm case fan

The Zyvpee AD0412HB-K96 is a 40 x 7 mm frame fan that runs on 12 V DC at 0.08 A. Its three-pin connector plugs directly into standard motherboard headers for simple speed reporting. The ball-bearing motor is rated below 1600 RPM and includes a small heatsink for targeted component cooling. Builders working in tight enclosures or on legacy boards will find the 4 cm footprint easy to place.

Replaces larger or sleeve-bearing units

When an existing 40 mm fan has become noisy or failed, this model restores airflow without requiring a mounting redesign. The ball bearing offers longer life than sleeve alternatives in continuous operation. The upgrade is worthwhile when the original cooler used a 3-pin header and the chassis cannot accommodate a thicker frame. It is not suited for builds that need higher static pressure or PWM control.

Steady output under constant load

At the rated 12 V the motor maintains its sub-1600 RPM speed without the rapid decay seen in sleeve-bearing designs. The attached heatsink helps dissipate heat from the motor itself during prolonged runs. Acoustic output remains consistent because the bearing preload does not shift with temperature. The fan is not designed for variable-speed curves or high-restriction radiators.

Kohokohdat

  • Compact 40 mm frame fits tight builds
  • Ball bearing runs below 1600 RPM for quiet operation
  • 12 V 0.08 A draw keeps power use low
  • 3-pin connector enables simple motherboard control
  • Two-tone non-LED design suits clean aesthetics

Tekniset tiedot

Brand3ccooler.com
SeriesAD0412HB-K96
ModelAD0412HB-K96
TypeCPU Cooler Fan
Bearing TypeBall
RPM<1600 RPM
Power Connector3 Pin
Color2-Tone
LEDNon-LED
FeaturesCPU Cooling

Kysymyksiä tästä tuotteesta

Will the 40 x 7 mm frame fit a standard 40 mm mounting hole pattern?

Yes, the 40 mm square frame with 7 mm thickness matches the common 40 mm hole spacing used on many small heatsinks and tight chassis.

How do I connect the three-pin lead so the motherboard reads RPM correctly?

Align the keyed 3-pin connector with the motherboard header; the third wire is the tach signal — pushing it in offset by one pin is the usual mistake.

When should I plan to replace the ball-bearing fan?

The ball bearing is rated for continuous 12 V 0.08 A operation; expect long service life before any RPM drop or noise increase signals a swap.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.