Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black 80 mm maglev case fan, 25 mm thick, two-pin connector

Zyvpee

Zyvpee KDE1208PTV1 80 mm 12 V 1.6 W 2-pin maglev case fan

SKU CH-P70X-1EWET

An 80 mm maglev case fan running at up to 1600 RPM on 12 V and 1.6 W for CPU cooling

  • TypeCase Fan
  • CompatibilityCPU Cooler
  • Bearing TypeMaglev
  • RPM<1600 RPM
  • Power Connector2 Pin
  • ColorBlack
  • Maglev bearing reduces friction for quieter operation
  • 12 V 1.6 W draw keeps power consumption low
  • 80 mm by 25 mm frame fits standard CPU coolers
  • 2-pin connector offers simple installation
  • Speed stays below 1600 RPM for balanced airflow

80 mm maglev case fan

The Zyvpee KDE1208PTV1 is an 80 mm case fan built with a maglev bearing for reduced friction and quiet operation. It runs on 12 V DC power and draws 1.6 W, spinning at speeds below 1600 RPM. The frame measures 80 by 25 mm and carries a black, non-LED finish. A two-pin connector supplies power without a PWM control line.

Suitable for compact CPU coolers and tight chassis

This fan fits builds that need an 80 mm mounting pattern and a thin 25 mm profile, such as small-form-factor CPU coolers or space-constrained enclosures. The two-pin power connector means speed is regulated by voltage only, so it is not suited for systems that require four-pin PWM control or software-driven fan curves. Buyers who need addressable lighting or a taller frame should look elsewhere.

Maglev bearing for low-noise longevity

The maglev bearing suspends the rotor magnetically, minimising mechanical contact and wear while keeping acoustic output low at the stated sub-1600 RPM ceiling. This single characteristic determines whether the fan meets a build’s noise and reliability targets.

Kohokohdat

  • Maglev bearing reduces friction for quieter operation
  • 12 V 1.6 W draw keeps power consumption low
  • 80 mm by 25 mm frame fits standard CPU coolers
  • 2-pin connector offers simple installation
  • Speed stays below 1600 RPM for balanced airflow

Tekniset tiedot

BrandZyvpee
SeriesKDE1208PTV1
ModelKDE1208PTV1
TypeCase Fan
CompatibilityCPU Cooler
Bearing TypeMaglev
RPM<1600 RPM
Power Connector2 Pin
ColorBlack
LEDNon-LED
FeaturesCPU Cooling Fan
Dimensions80*25MM

Kysymyksiä tästä tuotteesta

How loud and hot does the 80 mm 12 V 1.6 W maglev fan run at its maximum 1600 RPM when it operates continuously?

The maglev bearing reduces friction, so the 80 mm fan stays relatively quiet and cool even at the listed 1600 RPM ceiling during all-day use.

What power connector must my motherboard or fan controller provide for this 2-pin 12 V cooler?

A standard 2-pin 12 V header is required; the fan draws 1.6 W through two wires with no PWM or RGB leads.

Will the 80*25 mm frame line up with the mounting holes on my older CPU cooler that uses 80 mm fans?

Yes, the 80 mm by 25 mm dimensions match the common 8025 spacing used on many legacy CPU coolers.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.