Atermiter AT-X99 Intel motherboard with Xeon E5-2660 V3 and 32GB DDR4 REG ECC
- LGA 2011-v3
- Intel Core 5th gen…
Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.
Atermiter
Embedded X99 motherboard kit with Xeon E5-2670 V3 and 32 GB DDR4 REG ECC memory
Option X99-2670V3-32GB 3200Mhz(16GB x 2pcs ECC)
The Atermiter AT-X99 bundle pairs an Intel Xeon E5-2670 V3 with 32 GB of DDR4 REG ECC memory on an LGA 2011-v3 board. It arrives assembled and tested so system integrators and lab builders can deploy a validated compute node without sourcing separate components. The combination targets workloads that benefit from registered ECC stability such as rendering farms, simulation clusters or virtualization hosts.
Under continuous load the Xeon E5-2670 V3 runs its cores at the processor's rated frequencies while the memory controller limits the 3200 MHz modules to 2133 MHz. The registered ECC design detects and corrects single-bit errors in real time, preventing silent data corruption during multi-day compute jobs. Thermal output remains consistent because the chipset and voltage regulation are sized for the supported 2011-v3 series rather than burst-only operation.
This kit replaces a consumer desktop platform that cannot accept registered ECC modules or a mixed-memory configuration the board forbids. The jump is worth it when the workload demands error-correcting memory across all four slots and a validated Xeon rather than a desktop CPU on a workstation chipset. Builders who need non-ECC UDIMM populations or a different chipset feature set should look elsewhere.
| CPU Socket Type | LGA 2011-v3 |
|---|---|
| CPU Type | Intel Core 5th gen (LGA 2011-v3) |
Druge verzije ovog modela
Ista obitelj, različita memorija, hladnjak ili frekvencija — usporedite prije kupnje.
The board uses a 24-pin plus 8-pin power connection to feed the CPU and memory; sustained load will draw substantial current, so a chassis with good airflow and a cooler rated for high-wattage LGA 2011-v3 processors is essential.
You must supply a graphics card for the PCI-E x16 slot, storage drives, a case that fits the 235 mm by 185 mm board, and a PSU with both 24-pin and 8-pin CPU connectors.
The board cannot mix ECC and non-ECC modules; all four slots must use the same type, so you would need to replace any UDIMM sticks with REG ECC memory.
Također u ovoj kategoriji
Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.
Ono što šaljete, i ono u čemu gledate cijene.
Poslano iz Vašeg novčanika na blagajni
Samo prikaz — katalog je izražen u dolarima
Nijedna valuta ne odgovara.
Odaberite jezik na kojem Vam se stranica obraća.
Novi ste ovdje?
Već imate račun?
Ne postoji automatsko resetiranje: ova trgovina ne šalje e-poštu, stoga ne postoji jednokratna poveznica koju biste mogli zatražiti. Ostavite adresu uz svoj račun, netko će je ručno obraditi.
Zahtjev zaprimljen
Ništa neće stići u Vaš pretinac e-pošte — ova trgovina uopće ne šalje e-poštu. Netko će to ručno preuzeti.
Sjetili ste se?