Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in

Atermiter

Atermiter AT-X99 embedded solution with Xeon E5-2670 V3 and 32 GB DDR4 REG ECC

SKU CH-YW4W-0R2W1 MPN AT-X99

Embedded X99 motherboard kit with Xeon E5-2670 V3 and 32 GB DDR4 REG ECC memory

  • CPU Socket TypeLGA 2011-v3
  • CPU TypeIntel Core 5th gen (LGA 2011-v3)

Option X99-2670V3-32GB 3200Mhz(16GB x 2pcs ECC)

  • Pre-configured Xeon E5-2670 V3 with 32 GB REG ECC
  • 32 GB DDR4 3200 MHz memory runs at CPU-limited 2133 MHz
  • Embedded X99 board fits 235 × 185 mm footprint
  • Four DDR4 slots allow ECC-only or UDIMM-only populations
  • 24-pin plus 8-pin power inputs for stable delivery

Ready-to-run Xeon workstation base

The Atermiter AT-X99 bundle pairs an Intel Xeon E5-2670 V3 with 32 GB of DDR4 REG ECC memory on an LGA 2011-v3 board. It arrives assembled and tested so system integrators and lab builders can deploy a validated compute node without sourcing separate components. The combination targets workloads that benefit from registered ECC stability such as rendering farms, simulation clusters or virtualization hosts.

Sustained-load behaviour with registered ECC

Under continuous load the Xeon E5-2670 V3 runs its cores at the processor's rated frequencies while the memory controller limits the 3200 MHz modules to 2133 MHz. The registered ECC design detects and corrects single-bit errors in real time, preventing silent data corruption during multi-day compute jobs. Thermal output remains consistent because the chipset and voltage regulation are sized for the supported 2011-v3 series rather than burst-only operation.

Upgrade path from consumer or mixed-memory builds

This kit replaces a consumer desktop platform that cannot accept registered ECC modules or a mixed-memory configuration the board forbids. The jump is worth it when the workload demands error-correcting memory across all four slots and a validated Xeon rather than a desktop CPU on a workstation chipset. Builders who need non-ECC UDIMM populations or a different chipset feature set should look elsewhere.

I korthet

  • Pre-configured Xeon E5-2670 V3 with 32 GB REG ECC
  • 32 GB DDR4 3200 MHz memory runs at CPU-limited 2133 MHz
  • Embedded X99 board fits 235 × 185 mm footprint
  • Four DDR4 slots allow ECC-only or UDIMM-only populations
  • 24-pin plus 8-pin power inputs for stable delivery

Specifikationer

CPU Socket TypeLGA 2011-v3
CPU TypeIntel Core 5th gen (LGA 2011-v3)

Andra versioner av den här modellen

3 till i samma serie

Samma familj, men olika minne, kylning eller klockfrekvens — jämför innan du bestämmer dig.

Frågor om den här produkten

How much heat and noise should I expect from the Xeon E5-2670 V3 running continuously on this board?

The board uses a 24-pin plus 8-pin power connection to feed the CPU and memory; sustained load will draw substantial current, so a chassis with good airflow and a cooler rated for high-wattage LGA 2011-v3 processors is essential.

What other parts do I need to have on hand before this embedded solution will boot?

You must supply a graphics card for the PCI-E x16 slot, storage drives, a case that fits the 235 mm by 185 mm board, and a PSU with both 24-pin and 8-pin CPU connectors.

Will my existing DDR4 UDIMM sticks work alongside the supplied 32 GB REG ECC kit?

The board cannot mix ECC and non-ECC modules; all four slots must use the same type, so you would need to replace any UDIMM sticks with REG ECC memory.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.