Atermiter AT-X99 Intel motherboard with Xeon E5-2660 V3 and 32GB DDR4 REG ECC
- LGA 2011-v3
- Intel Core 5th gen…
Vi tager imod kryptovaluta — så den krypto, du ejer, kan købe rigtig hardware.Betal med krypto, brug det på rigtig hardware. Gratis, forsikret levering til hele verden ved køb over 399 $. Neutrale, umærkede papkasser, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Din kurs låses i 30 minutter, så snart kassen åbner.Kurs låst i 30 minutter. Hver vare er forseglet, har kontrolleret serienummer og er dækket af 24 måneders garanti.Forseglet, 24 måneders garanti.
Atermiter
Embedded X99 motherboard kit with Xeon E5-2670 V3 and 32 GB DDR4 REG ECC memory
Option X99-2670V3-32GB 3200Mhz(16GB x 2pcs ECC)
The Atermiter AT-X99 bundle pairs an Intel Xeon E5-2670 V3 with 32 GB of DDR4 REG ECC memory on an LGA 2011-v3 board. It arrives assembled and tested so system integrators and lab builders can deploy a validated compute node without sourcing separate components. The combination targets workloads that benefit from registered ECC stability such as rendering farms, simulation clusters or virtualization hosts.
Under continuous load the Xeon E5-2670 V3 runs its cores at the processor's rated frequencies while the memory controller limits the 3200 MHz modules to 2133 MHz. The registered ECC design detects and corrects single-bit errors in real time, preventing silent data corruption during multi-day compute jobs. Thermal output remains consistent because the chipset and voltage regulation are sized for the supported 2011-v3 series rather than burst-only operation.
This kit replaces a consumer desktop platform that cannot accept registered ECC modules or a mixed-memory configuration the board forbids. The jump is worth it when the workload demands error-correcting memory across all four slots and a validated Xeon rather than a desktop CPU on a workstation chipset. Builders who need non-ECC UDIMM populations or a different chipset feature set should look elsewhere.
| CPU Socket Type | LGA 2011-v3 |
|---|---|
| CPU Type | Intel Core 5th gen (LGA 2011-v3) |
Andre versioner af denne model
Samme familie, men med anden hukommelse, køler eller clockfrekvens — sammenlign, før du bestemmer dig.
The board uses a 24-pin plus 8-pin power connection to feed the CPU and memory; sustained load will draw substantial current, so a chassis with good airflow and a cooler rated for high-wattage LGA 2011-v3 processors is essential.
You must supply a graphics card for the PCI-E x16 slot, storage drives, a case that fits the 235 mm by 185 mm board, and a PSU with both 24-pin and 8-pin CPU connectors.
The board cannot mix ECC and non-ECC modules; all four slots must use the same type, so you would need to replace any UDIMM sticks with REG ECC memory.
Også på denne hylde
Samme hylde, samme kasse — otte mønter og 30 minutters kurslås.
Det du betaler med, og det du ser priserne i.
Sendes fra din tegnebog i kassen
Kun til visning — kataloget er prissat i USD
Ingen valuta matcher det.
Vælg det sprog, siden taler til dig på.
Ny her?
Har du allerede en?
Der findes ingen automatisk nulstilling: denne butik sender ingen e-mails, så der er intet engangslink at bede om. Efterlad adressen på kontoen, så bliver den behandlet manuelt.
Anmodning registreret
Der er intet på vej til din indbakke — denne butik sender slet ingen e-mails. Nogen behandler dem manuelt.
Kom du i tanke om den?