BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.
Corsair
32 GB DDR4 desktop memory kit running at 3200 MT/s with CL16 timings and a low-profile aluminum heatspreader
This Corsair Vengeance LPX kit delivers 32 GB of DDR4 memory in a matched 2 x 16 GB configuration rated for 3200 MT/s. It targets enthusiasts and builders who want reliable high-frequency performance for gaming or content creation without fitting tall heatspreaders.
Each module uses a pure aluminum heatspreader and an eight-layer PCB to move heat away from the ICs during sustained loads. The low-profile height keeps airflow clear around large CPU coolers, and the 1.35 V operating voltage limits power draw while maintaining the rated 16-20-20-38 timings.
Individually screened ICs and Intel XMP 2.0 profiles give straightforward one-click setup on tested Intel 100, 300, 400, 500 Series and X299 platforms, plus AMD 300, 400, 500 Series and X570 boards. The 288-pin DIMMs suit standard desktop slots, but buyers needing four-module populations or ECC support should look elsewhere.
Za ovaj artikl još nisu objavljene specifikacije.
Align the notch on each 288-pin stick with the slot key, press firmly until the retention clips click, then enter the motherboard BIOS and enable the Intel XMP 2.0 profile so the kit runs at its rated 3200 speed instead of the default JEDEC frequency.
The heatspreader and PCB are passive components with no moving parts; occasional dust removal with compressed air is the only upkeep required, and no thermal-pad replacement or re-torquing is specified for this kit.
The modules are rated to operate at 1.35 V; pushing voltage beyond that spec risks instability and can trigger the motherboard's protection circuits, so the voltage ceiling is the first hard limit encountered when scaling frequency or tightening timings beyond the XMP 2.0 profile.
Također u ovoj kategoriji
Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.
Ono što šaljete, i ono u čemu gledate cijene.
Poslano iz Vašeg novčanika na blagajni
Samo prikaz — katalog je izražen u dolarima
Nijedna valuta ne odgovara.
Odaberite jezik na kojem Vam se stranica obraća.
Nema odgovarajućeg jezika.
Novi ste ovdje?
Već imate račun?
Ne postoji automatsko resetiranje: ova trgovina ne šalje e-poštu, stoga ne postoji jednokratna poveznica koju biste mogli zatražiti. Ostavite adresu uz svoj račun, netko će je ručno obraditi.
Zahtjev zaprimljen
Ništa neće stići u Vaš pretinac e-pošte — ova trgovina uopće ne šalje e-poštu. Netko će to ručno preuzeti.
Sjetili ste se?