Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.

Praćeni artikli Prijava
White silk PLA filament spool, 1.75 mm diameter, 1 kg net weight

PrintOxe

PrintOxe PLA like SILK White 1.75 mm 1 Kg 3D printers accessory

SKU CH-24D4-BKCY3

White silk-finish PLA filament, 1.75 mm diameter, 1 kg spool with ±.03 mm accuracy for glossy prints

  • ColorWhite
  • TypeFilament

Color White

  • Silk texture delivers a glossy, shiny surface finish
  • Dimensional accuracy of +/- .03 mm ensures precise extrusion
  • 75 mm diameter fits most popular desktop 3D printers
  • Vacuum-sealed spool with desiccant protects filament from moisture
  • Prints at 200 °C to 220 °C for reliable layer adhesion

1 kg Silk PLA Filament

PrintOxe PLA like SILK White is a 1.75 mm diameter filament supplied on a 1 kg spool. The material uses a high-gloss silk formula that produces a shiny surface finish on printed parts. It is vacuum-sealed with desiccant to protect against moisture. Dimensional accuracy is held to +/- 0.03 mm for consistent extrusion.

Suits FDM printers using 1.75 mm PLA

This filament works with many popular FDM printers including MakerBot, Reprap, Afinia, UP, Mendel, Flashforge, Solidoodle 2, Printrbot LC and MakerGear M2. The recommended nozzle temperature range is 200°C to 220°C. Builders needing a different diameter, a higher temperature material, or a larger spool size should look at other products.

+/- 0.03 mm dimensional accuracy

The +/- 0.03 mm tolerance is the key specification that determines whether this filament will feed reliably in a given extruder. Tight diameter control reduces the risk of jams and helps maintain steady flow rates. If a printer requires tighter or looser tolerances, this figure decides compatibility.

Istaknuto

  • Silk texture delivers a glossy, shiny surface finish
  • Dimensional accuracy of +/- .03 mm ensures precise extrusion
  • 75 mm diameter fits most popular desktop 3D printers
  • Vacuum-sealed spool with desiccant protects filament from moisture
  • Prints at 200 °C to 220 °C for reliable layer adhesion

Specifikacije

BrandPrintOxe
ModelPLA like SILK
ColorWhite
TypeFilament

Druge verzije ovog modela

još 5 u istoj seriji

Ista obitelj, različita memorija, hladnjak ili frekvencija — usporedite prije kupnje.

Pitanja o ovom artiklu

Does the 1.75 mm filament need active cooling or an enclosure when printing for hours?

PLA like SILK prints at 200 °C to 220 °C and is designed for minimal warping, so a standard part-cooling fan is usually enough; an enclosure is not required.

My printer uses a 2.20 inch hub hole — will this spool fit?

The spool hub hole is 2.20 inches (5.59 cm), matching many common printers; check your holder width against the 2.69 inch (6.83 cm) spool width.

Will the +/- 0.03 mm tolerance work reliably on my older Bowden setup?

The tight 0.03 mm diameter accuracy reduces extrusion variance, helping older Bowden printers avoid clogging and under-extrusion.

Također u ovoj kategoriji

Kupci su usporedili ovo

Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.