Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green PCB adapter card with M.2 slots and PCIe connector

Corn Electronics

Corn Electronics JEYI SK6 M.2 NVMe & NGFF SSD to PCI-E 3.0 x4 Adapter

SKU CH-RSTJ-F5AZ7

Converts M.2 NVMe and SATA SSDs up to 110 mm to a PCI-E 3.0 x4 slot with no driver required

  • Supports M.2 lengths 2230 2242 2260 2280 and 110 mm
  • Tantalum capacitors protect your SSD from power surges
  • PCIe 3.0 x4 delivers up to 8 GB/s throughput
  • Works with NVMe M-Key and SATA B-Key drives
  • Driver-free installation on any compatible motherboard

Dual-Protocol M.2 Adapter

The Corn Electronics JEYI SK6 adapter accepts both M-key NVMe and B-key SATA M.2 drives in lengths from 2230 to 110 mm. It connects the NVMe drive through a PCIe 3.0 x4 slot and the SATA drive through a motherboard SATA port. No driver installation is required for either mode.

Passive Thermal Design

The card uses tantalum capacitors to protect the attached SSD during power transitions. Because it has no active cooling, thermals and noise depend entirely on the host system airflow and the drive’s own controller. Power draw is limited to what the PCIe slot and SATA connector can supply.

Sustained Transfer Behaviour

Under continuous load the adapter maintains the PCIe 3.0 x4 electrical link, so throughput stays at the drive’s rated limit rather than throttling after a short burst. The twin-slot layout lets both an NVMe and a SATA drive operate simultaneously without sharing bandwidth.

Helstu kostir

  • Supports M.2 lengths 2230 2242 2260 2280 and 110 mm
  • Tantalum capacitors protect your SSD from power surges
  • PCIe 3.0 x4 delivers up to 8 GB/s throughput
  • Works with NVMe M-Key and SATA B-Key drives
  • Driver-free installation on any compatible motherboard

Tæknilýsing

Engin birt tæknilýsing fyrir þessa vöru enn.

Spurningar um þessa vöru

How do I install the JEYI SK6 adapter and which slot do I use for an NVMe drive?

Insert the NVMe M-Key SSD into the M.2 slot on the card, secure it with the adjustable standoff matching 2230 to 110 mm lengths, then plug the card into a motherboard PCIe 3.0 x4, x8 or x16 slot; no driver is required.

What maintenance or replacement will the JEYI SK6 adapter need over time?

The on-board tantalum capacitors protect the SSD and are not user-serviceable; if a capacitor fails the whole adapter card must be replaced.

What speed limit appears first when the JEYI SK6 runs sustained transfers?

The PCIe 3.0 x4 interface caps throughput at 8 GB/s, so sustained reads and writes cannot exceed that bandwidth.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.