暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Green PCB adapter card with M.2 slots and PCIe connector

Corn Electronics

Corn Electronics JEYI SK6 M.2 NVMe & NGFF SSD to PCI-E 3.0 x4 Adapter

SKU CH-RSTJ-F5AZ7

Converts M.2 NVMe and SATA SSDs up to 110 mm to a PCI-E 3.0 x4 slot with no driver required

  • Supports M.2 lengths 2230 2242 2260 2280 and 110 mm
  • Tantalum capacitors protect your SSD from power surges
  • PCIe 3.0 x4 delivers up to 8 GB/s throughput
  • Works with NVMe M-Key and SATA B-Key drives
  • Driver-free installation on any compatible motherboard

Dual-Protocol M.2 Adapter

The Corn Electronics JEYI SK6 adapter accepts both M-key NVMe and B-key SATA M.2 drives in lengths from 2230 to 110 mm. It connects the NVMe drive through a PCIe 3.0 x4 slot and the SATA drive through a motherboard SATA port. No driver installation is required for either mode.

Passive Thermal Design

The card uses tantalum capacitors to protect the attached SSD during power transitions. Because it has no active cooling, thermals and noise depend entirely on the host system airflow and the drive’s own controller. Power draw is limited to what the PCIe slot and SATA connector can supply.

Sustained Transfer Behaviour

Under continuous load the adapter maintains the PCIe 3.0 x4 electrical link, so throughput stays at the drive’s rated limit rather than throttling after a short burst. The twin-slot layout lets both an NVMe and a SATA drive operate simultaneously without sharing bandwidth.

特長

  • Supports M.2 lengths 2230 2242 2260 2280 and 110 mm
  • Tantalum capacitors protect your SSD from power surges
  • PCIe 3.0 x4 delivers up to 8 GB/s throughput
  • Works with NVMe M-Key and SATA B-Key drives
  • Driver-free installation on any compatible motherboard

仕様

この商品の仕様はまだ公開されていません。

この商品に関する質問

How do I install the JEYI SK6 adapter and which slot do I use for an NVMe drive?

Insert the NVMe M-Key SSD into the M.2 slot on the card, secure it with the adjustable standoff matching 2230 to 110 mm lengths, then plug the card into a motherboard PCIe 3.0 x4, x8 or x16 slot; no driver is required.

What maintenance or replacement will the JEYI SK6 adapter need over time?

The on-board tantalum capacitors protect the SSD and are not user-serviceable; if a capacitor fails the whole adapter card must be replaced.

What speed limit appears first when the JEYI SK6 runs sustained transfers?

The PCIe 3.0 x4 interface caps throughput at 8 GB/s, so sustained reads and writes cannot exceed that bandwidth.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。